If your 2008 or 2009 Chevy Suburban 1500 is suddenly stalling, hesitating on acceleration, or refusing to start, a failing Fuel Pump Control Module (FPCM) is a very likely culprit. As a mechanic with over two decades of experience, I’ve seen countless vehicle owners waste money replacing a perfectly good fuel pump when this module was the real problem. This isn’t just a replacement part; it’s a complete, ready-to-install solution for a common and frustrating issue.
The FPCM, also known as a Fuel Pump Driver Module, is the brain that tells your fuel pump how much pressure to deliver. When it fails, your engine is starved of fuel, leading to poor performance and a variety of check engine light codes. Our module solves this problem by arriving at your door fully programmed to your vehicle’s specific VIN with the latest GM software updates. This means you can skip the expensive trip to the dealership for programming—a service that can often cost as much as the part itself, not to mention the hassle of a tow.
Case Study: A Tricky Diagnosis
A customer brought in a 2008 Yukon XL (which uses the same system as the Suburban) with a classic no-start condition. They had already replaced the in-tank fuel pump themselves, but the truck still wouldn’t fire up. Their scanner showed a U0109 code—Lost Communication With Fuel Pump Control Module. A quick check of the FPCM, mounted on the driver-side frame rail, revealed heavy corrosion on the casing and connector. After installing one of our pre-programmed modules, the truck started instantly. This is a perfect example of how diagnosing the correct component first saves time, money, and headaches.
Common Signs of a Failing FPCM
If you’re experiencing any of the following, your Fuel Pump Control Module may be at the end of its life. Look out for these tell-tale signs:
- ✔ Engine cranks but will not start
- ✔ Stalling, especially under load or when warm
- ✔ Vehicle hesitation or stumbling during acceleration
- ✔ Reduced engine power and poor fuel economy
- ✔ Check Engine Light with codes like P069E, U0109, or P0230
A Straightforward Guide to Installation
Replacing the 2008-2009 Suburban 1500 FPCM is a job most DIYers can handle with basic tools. The module is typically located on the driver’s side frame rail, near the spare tire.
- Safety First: Disconnect the negative terminal from your vehicle’s battery.
- Locate the Module: Find the FPCM mounted to the vehicle’s frame. It’s a small silver or black box with an electrical connector.
- Disconnect and Remove: Carefully unplug the electrical connector. Then, remove the bolts or nuts securing the module to the frame. These can sometimes be corroded, so a little penetrating oil might help.
- Install the New Module: Bolt the new, pre-programmed FPCM into the original location. Ensure it is securely mounted.
- Reconnect and Test: Plug the electrical connector firmly into the new module. Reconnect the battery terminal, turn the key to the ‘On’ position for a few seconds to prime the system, and then start the engine.
Verified Vehicle Compatibility
This module is a direct-fit replacement for a wide range of GM vehicles. We guarantee compatibility if your vehicle is listed below. This part is an exact replacement for part numbers: 13501024, 15213110, 20759945, 20850907, 25785013, 25854536, 25866052, and 25967325.
- ACADIA 2009 (Fuel Pump)
- AVALANCHE 1500 2008-2009 (Fuel Pump; LH frame rail)
- CANYON / COLORADO 2009 (Fuel Pump; rear center frame)
- ENCLAVE 2009 (Fuel Pump)
- ESCALADE / ESV / EXT 2008-2009 (Fuel Pump; LH frame rail)
- EXPRESS / SAVANA 1500 VAN 2008-2009 (Fuel Pump; LH frame rail)
- HUMMER H2 2008-2009 (Fuel Pump; LH frame rail)
- HUMMER H3 2009 (Fuel Pump; rear frame)
- OUTLOOK 2009 (Fuel Pump)
- SIERRA 1500 / SILVERADO 1500 PICKUP 2007 (New Style, smooth door skin), 2008-2009 (Fuel Pump; LH frame rail)
- SIERRA DENALI 2008-2009 (Fuel Pump; LH frame rail)
- SUBURBAN 1500 2008-2009 (Fuel Pump; LH frame rail)
- TAHOE 2008-2009 (Fuel Pump; LH frame rail)
- TRAVERSE 2009 (Fuel Pump; rear crossmember)
- VUE 2008-2009 (Fuel Pump; RH rear engine compartment)
- YUKON / YUKON XL 1500 2008-2009 (Fuel Pump; LH frame rail)
By purchasing this 2008-2009 Suburban 1500 FPCM, you’re getting a reliable, plug-and-play part that restores your vehicle’s performance without the dealership hassle. Just provide your VIN at checkout, and we’ll handle the rest.
Frequently Asked Questions
Do I need to get this module programmed by a dealer?
No! That’s the best part. We program the module to your specific vehicle using your VIN before we ship it. It arrives ready for a plug-and-play installation.
How do I provide my VIN?
After you complete your purchase, you will receive instructions to reply with your 17-digit Vehicle Identification Number (VIN). We cannot ship the part until we receive your VIN.
Where is the FPCM located on my 2009 Suburban?
On the 2008-2009 Suburban 1500, the Fuel Pump Control Module is typically mounted on the outside of the driver’s side frame rail, often near the spare tire area.
Will this fix a P069E check engine code?
Yes, a P069E code (Fuel Pump Control Module Requested MIL Illumination) is one of the most common diagnostic trouble codes indicating a faulty FPCM. Replacing it with our pre-programmed unit is the correct fix in most cases.
Is this compatible with other part numbers?
Yes, this module is a direct replacement for several part numbers, including 20759945, 13501024, and 25967325. Please see the full compatible list in the description above.