If your 2007-2009 Silverado 1500 is experiencing sudden stalling, hard starting, or a frustrating “Reduced Engine Power” message, the culprit is often not the fuel pump itself, but this critical component: the Fuel Pump Control Module (FPCM). As a technician with over two decades of experience, I’ve seen countless vehicle owners and even shops misdiagnose this issue, leading to wasted money on a new fuel pump when the FPCM was the real problem all along. This module, also known as a Fuel Pump Driver Module, is the brain behind your fuel delivery system, and when it fails, it can leave you stranded without warning.
This isn’t just a replacement part; it’s a complete, ready-to-install solution. We take the guesswork and extra cost out of the repair by pre-programming this module to your truck’s specific Vehicle Identification Number (VIN) before it ships. This means you get the latest GM software updates for optimal performance and reliability, without needing a trip to the dealership or access to expensive diagnostic tools. It’s a true plug-and-play fix designed to get you back on the road with confidence.
From the Diagnostic Bay: The “Bad” Fuel Pump That Wasn’t
I remember a customer coming into the shop, frustrated after already replacing the fuel pump on his ’08 Sierra himself. The truck would start, run for a few seconds, and then die. He was convinced he got a faulty pump. After hooking up my scan tool, I saw no fuel pressure command from the ECU. Instead of looking at the pump, I went straight to the FPCM, located on the driver-side frame rail. It was corroded and water-damaged—a common fate for these modules. We installed a new, programmed FPCM, and the truck fired right up and ran perfectly. He had spent hundreds on a pump he didn’t need. This story is why we offer this pre-programmed 2007-2009 Silverado 1500 FPCM; it’s the right fix, the first time.
Is Your Truck Showing These Symptoms?
A failing FPCM can mimic a bad fuel pump. Before you spend hundreds on the wrong part, see if your vehicle is exhibiting these common signs of a faulty fuel pump control module:
- ✔ Engine stalls unexpectedly, especially while driving
- ✔ Vehicle will not start or is very difficult to start
- ✔ Engine starts but dies after a few seconds
- ✔ “Reduced Engine Power” message displayed on the dash
- ✔ Check Engine Light with diagnostic trouble codes (DTCs) such as P069E, P0230, or U0109
- ✔ Inconsistent fuel pressure readings
A Straightforward Guide to Installation
Installing your new FPCM is a simple process that most DIYers can complete in under an hour with basic hand tools. This pre-programmed module makes the job even easier.
- Safety First: Disconnect the negative terminal from your vehicle’s battery.
- Locate the Module: On most GM trucks and SUVs like the Silverado, the FPCM is mounted to the driver’s side frame rail, often near the spare tire.
- Disconnect and Remove: Unplug the electrical connector(s) from the old module. Then, remove the bolts or nuts holding it to the frame.
- Install the New Module: Mount your new, pre-programmed FPCM in the same location and secure it with the original hardware.
- Reconnect: Plug the electrical connector(s) firmly into the new module. Reconnect your battery terminal.
- Final Step: Start the vehicle. The engine should now run smoothly, with the Check Engine Light off.
Verified Vehicle Compatibility
This module is a direct-fit replacement for a wide range of GM vehicles and interchanges with multiple part numbers, ensuring broad compatibility. Please verify your vehicle is on the list below. This part is a reliable solution for your 2007-2009 Silverado 1500 FPCM needs and many other models.
Compatible Part Numbers: 13501024, 15213110, 20759945, 20850907, 25785013, 25854536, 25866052, 25967325
- ACADIA 09
- AVALANCHE 1500 08-09
- CANYON / COLORADO 09
- ENCLAVE 09
- ESCALADE / ESV / EXT 08-09
- EXPRESS / SAVANA 1500 VAN 08-09
- HUMMER H2 08-09
- HUMMER H3 09
- OUTLOOK 09
- SIERRA 1500 PICKUP 07 (New Body Style) & 08-09
- SIERRA DENALI 08-09
- SILVERADO 1500 PICKUP 07 (New Body Style) & 08-09
- SUBURBAN 1500 08-09
- TAHOE 08-09
- TRAVERSE 09
- VUE 08-09
- YUKON / YUKON XL 1500 08-09
Frequently Asked Questions
Do I need to program this module?
No. This Fuel Pump Control Module comes fully programmed to your vehicle’s VIN. Just provide us with your VIN at checkout, and it will arrive ready to install right out of the box.
Where is the FPCM located on my 2008 Silverado?
On most 2007-2009 GM trucks and SUVs, including the Silverado 1500, the FPCM is mounted on the outside of the driver-side frame rail, typically above the spare tire area.
How do I provide my VIN?
After you complete your purchase, simply send us a message with your 17-digit Vehicle Identification Number (VIN). We cannot ship the module until we receive your VIN to program it.
Will this fix a P069E trouble code?
Yes, the DTC P069E (Fuel Pump Control Module Requested MIL Illumination) is one of the most common codes indicating a failed FPCM. Replacing the module with this pre-programmed unit is the correct repair for this code.
Is this different from the fuel pump?
Yes. The fuel pump is located inside your fuel tank and physically pumps the fuel. This module is an external electronic controller that tells the fuel pump how fast to run based on engine demand.