Restore Peak Performance and Reliability to Your GM Vehicle
Are you battling frustrating issues like your engine cranking but not starting, sudden stalling while driving, or a persistent Check Engine Light? These are classic signs of a failing Fuel Pump Control Module (FPCM), a critical component that regulates power to your fuel pump. When it falters, it can leave you stranded. This isn’t just an inconvenience; it’s a safety concern. We offer a direct, dependable solution: a replacement 2009 Acadia Fuel Pump Control Module that arrives at your door fully programmed and ready for installation.
Case Study: A Tricky Diagnosis
I remember a 2009 GMC Sierra in my bay a few months back. The owner had been to two other shops for an intermittent stalling problem that nobody could pinpoint. The truck would run fine for days, then die at a stoplight without warning. It threw a U0109 (Lost Communication with Fuel Pump Control Module) code, but only sporadically. After checking the wiring and fuel pump, I focused on the FPCM itself. These modules, especially on trucks, are exposed to brutal conditions on the frame rail—water, salt, and vibration. I’ve seen hundreds fail from internal corrosion. We installed one of our VIN-programmed modules, and the problem was solved instantly. The key was not just replacing the part, but ensuring it had the latest GM software to prevent the communication dropouts the original was prone to.
Is Your GM Vehicle Showing These Signs?
A faulty FPCM can manifest in several ways. If you’re experiencing any of the following, this module is the likely solution.
- ✔ Engine cranks but will not start
- ✔ Vehicle stalls unexpectedly, especially under load or when warm
- ✔ Hesitation or stumbling during acceleration
- ✔ Reduced engine power and poor fuel economy
- ✔ Check Engine Light with codes like P069E, U0109, or P0230
The Critical Advantage: Pre-Programmed for Your Vehicle
Normally, replacing an FPCM requires a trip to the dealership for expensive programming with their specialized tools. Our process eliminates that step entirely. You provide us with your Vehicle Identification Number (VIN) during checkout, and our technicians will flash this module with the latest, most stable GM software specific to your vehicle. This ensures perfect communication between the FPCM and your vehicle’s computer (ECM), restoring factory performance and reliability right out of the box. This is the definitive fix for your 2009 Acadia Fuel Pump Control Module and other compatible GM models.
A Straightforward Guide to Installation
With the programming already handled, installation is a job most DIYers or any professional mechanic can complete with basic hand tools. While the exact location varies by model (see fitment list), the process is generally the same.
- Safety First: Always disconnect the negative terminal from your vehicle’s battery before starting any electrical work.
- Locate the Module: On most trucks and SUVs, the FPCM is mounted to the driver’s side frame rail, often near the spare tire. On vehicles like the Acadia or Traverse, it’s typically on a rear crossmember.
- Disconnect and Remove: Carefully unplug the electrical connectors. Be gentle with the locking tabs, as they can become brittle. Then, unbolt the old module from its mounting location.
- Install the New Module: Bolt the new, pre-programmed module into place. Ensure it is securely fastened.
- Reconnect and Test: Plug the electrical connectors firmly into the new module. Reconnect your battery terminal. Turn the key to the ‘On’ position for a few seconds to allow the system to prime, then start the vehicle.
Verified Vehicle Compatibility
This module is a direct replacement for a wide range of General Motors vehicles. Please verify your model and year below. This part is also a direct replacement for part numbers: 13501024, 15213110, 20759945, 20850907, 25785013, 25854536, 25866052, and 25967325.
- ACADIA 09 (Located on rear crossmember)
- AVALANCHE 1500 08-09 (Located on LH frame rail)
- CANYON / COLORADO 09 (Located on rear center frame)
- ENCLAVE 09 (Located on rear crossmember)
- ESCALADE / ESV / EXT 08-09 (Located on LH frame rail)
- EXPRESS 1500 VAN 08-09 (Located on LH frame rail)
- HUMMER H2 08-09 (Located on LH frame rail)
- HUMMER H3 09 (Located on rear frame)
- OUTLOOK 09
- SAVANA 1500 VAN 08-09 (Located on LH frame rail)
- SIERRA / SILVERADO 1500 PICKUP 07 (New body style, smooth door skin)
- SIERRA / SILVERADO 1500 PICKUP 08-09 (Located on LH frame rail)
- SIERRA DENALI 08-09 (Located on LH frame rail)
- SUBURBAN 1500 08-09 (Located on LH frame rail)
- TAHOE 08-09 (Located on LH frame rail)
- TRAVERSE 09 (Located on rear crossmember)
- VUE 08-09 (Located in RH rear engine compartment)
- YUKON / YUKON XL 1500 08-09 (Located on LH frame rail)
Frequently Asked Questions
How do I provide my VIN for programming?
After completing your purchase, you can send us your 17-digit VIN through the messaging system or add it as a note during checkout. We cannot ship the module until we receive your VIN.
Is this part truly plug-and-play?
Yes. Because we program it to your specific VIN before shipping, it requires no additional programming or setup. Simply install it, and your vehicle is ready to go.
What if I install it and my vehicle still doesn’t start?
While this module fixes the most common cause of these symptoms, a no-start condition can also be caused by a failed in-tank fuel pump or wiring issues. The FPCM is the most common and logical first step in the diagnosis, especially if you have FPCM-related trouble codes.
Will this fix my Check Engine Light?
If the light is on due to codes related to the Fuel Pump Control Module (like U0109 or P069E), this part will resolve the issue and allow the codes to be cleared.
Is this an original GM part?
This is a high-quality replacement part that is programmed using official GM software updates. It is designed to meet or exceed original equipment specifications for performance and longevity.