Restore Your Yukon’s Reliability and Performance
Is your 2008-2009 GMC Yukon XL 1500 suddenly stalling, struggling to start, or hesitating under acceleration? These are classic, frustrating signs of a failing Fuel Pump Control Module (FPCM), also known as a Fuel System Control Module (FSCM). This critical component regulates the voltage sent to your fuel pump, ensuring your engine gets the precise amount of fuel it needs. When it fails, it can leave you stranded. In my 20+ years in the shop, I’ve seen these modules cause some of the most intermittent and maddening diagnostic headaches for owners and technicians alike.
This isn’t just a replacement part; it’s a complete, ready-to-install solution. We take the hassle and expense out of the repair by pre-programming this module with the latest official GM software, tailored specifically to your vehicle’s VIN. This means you can skip the costly trip to the dealership for programming. You get a direct-fit part that restores original performance and reliability, right out of the box.
From the Diagnostic Bay: The Ghost in the Machine
A customer brought in their ’08 Silverado with a complaint that stumped two other shops: it would randomly stall at red lights, but only when the weather was hot and after driving for 30+ minutes. There were no consistent codes, just an occasional P069E (Fuel Pump Control Module Commanded OFF). We checked fuel pressure, which was erratic. Instead of just throwing a fuel pump at it, we focused on the FPCM, located on the frame rail. These modules are notorious for failing from heat and corrosion. We swapped in a pre-programmed module, and the problem vanished. The owner had spent nearly a thousand dollars chasing a ghost that was, in reality, a simple-to-replace module. This is why addressing the FPCM first can save you a fortune.
Is Your Truck Showing These Symptoms?
- ✔ Engine cranks but won’t start (no-start condition)
- ✔ Vehicle stalls unexpectedly, especially when warm or under load
- ✔ Hesitation or sputtering when you press the gas pedal
- ✔ Reduced engine power and poor fuel economy
- ✔ An active Check Engine Light with codes like P069E, P0230, or U0109
A Straightforward Guide to Installation
Replacing the 2008-2009 Yukon XL FPCM is a job most DIYers can handle with basic tools. The module is typically located on the driver-side frame rail, near the spare tire.
- Safety First: Disconnect the negative terminal from your vehicle’s battery.
- Locate the Module: Find the FPCM mounted to the vehicle’s frame. On most GM trucks and SUVs, it’s a small silver box held by two bolts.
- Disconnect the Wiring: Carefully unplug the electrical connector. There’s a locking tab you’ll need to release first.
- Remove the Old Module: Use a socket wrench to remove the two mounting bolts and take the old module off the frame.
- Install the New Module: Mount your new, pre-programmed FPCM in the same location and tighten the bolts securely.
- Reconnect and Finalize: Plug the electrical connector back in until it clicks. Reconnect the negative battery terminal. The vehicle is now ready to start with no further programming required.
Verified Vehicle Compatibility
This module is a direct replacement for part number 25967325 and is also compatible with part numbers: 13501024, 15213110, 20759945, 20850907, 25785013, 25854536, and 25866052. It is guaranteed to fit the following vehicles:
- Acadia: 2009
- Avalanche 1500: 2008-2009
- Canyon / Colorado: 2009
- Enclave: 2009
- Escalade / ESV / EXT: 2008-2009
- Express 1500 Van: 2008-2009
- Hummer H2: 2008-2009
- Hummer H3: 2009
- Outlook: 2009
- Savana 1500 Van: 2008-2009
- Sierra 1500 / Denali: 2007 (New Body Style), 2008-2009
- Silverado 1500: 2007 (New Body Style), 2008-2009
- Suburban 1500: 2008-2009
- Tahoe: 2008-2009
- Traverse: 2009
- Vue: 2008-2009
- Yukon / Yukon XL 1500: 2008-2009
Frequently Asked Questions
Do I need to do any programming after I install this?
No. This module arrives fully programmed to your vehicle’s VIN. It is a true plug-and-play solution, saving you a trip to the dealer.
What information do you need from me?
After you place your order, you must provide us with your 17-digit Vehicle Identification Number (VIN). We cannot ship the part until we have your VIN to program it correctly.
Where is the FPCM located on my 2008 Yukon XL?
On the 2008-2009 Yukon XL 1500, the Fuel Pump Control Module is typically mounted on the inside of the driver-side frame rail, often near the spare tire area.
Will this fix a P069E code?
Yes, a faulty FPCM is the most common cause of a P069E diagnostic trouble code. Replacing it with this pre-programmed unit is the standard, effective repair for this issue.
Is this a new or used part?
This is a high-quality, tested replacement part that has been programmed with the latest software from GM for optimal performance and longevity.