Restore Your Vehicle’s Performance and Reliability
Is your Saturn VUE, or another GM truck or SUV, suddenly stalling, hesitating, or refusing to start? Before you condemn the fuel pump, the real culprit is often a faulty Fuel Pump Control Module (FPCM). As a technician with over two decades of diagnostic experience, I’ve seen this exact scenario play out countless times. This module is the brain behind your fuel delivery system, and when it fails, it can cause a host of frustrating and intermittent problems. This replacement FPCM is your direct, hassle-free solution. We pre-program it to your vehicle’s specific VIN, loading the latest GM software updates. This means it arrives at your door ready for a simple, plug-and-play installation, saving you a costly trip to the dealership for programming.
From the Diagnostic Bay: The Stalling VUE
A customer brought in their 2008 Saturn VUE with a classic complaint: it would randomly stall at stoplights and was hard to restart. They had already replaced the fuel pump on a friend’s advice, but the problem persisted. After hooking up my scan tool, I noticed fluctuating fuel rail pressure and a stored DTC U0109 (Lost Communication With Fuel Pump Control Module). Instead of throwing more parts at it, we inspected the FPCM. On the VUE, it’s tucked in the right rear of the engine compartment, where heat and vibrations take their toll. A new, programmed module fixed the issue instantly. This story is why we offer this pre-programmed 2008-2009 VUE Fuel Pump Control Module—to get you the right fix the first time.
Is Your GM Vehicle Showing These Symptoms?
A failing FPCM can mimic a bad fuel pump. If you’re experiencing any of the following, this module is the likely solution:
- ✔ Engine cranking but not starting (no-start condition)
- ✔ Intermittent stalling, especially when coming to a stop or at idle
- ✔ Engine sputtering, hesitating, or surging during acceleration
- ✔ Reduced engine power and poor fuel economy
- ✔ A “Service Engine Soon” or Check Engine Light with codes like P069E, P0230, or U0109
A Straightforward Guide to Your FPCM Installation
Installing your new module is a job most DIYers can handle in under an hour. Since we program it beforehand, you won’t need any special scan tools.
- Safety First: Disconnect the negative terminal from your vehicle’s battery.
- Locate the Module: On the 2008-2009 Saturn VUE, the FPCM is located in the right-hand (passenger side) rear of the engine compartment. For most GM trucks and SUVs on the fitment list, it’s mounted on the driver-side frame rail, near the spare tire.
- Disconnect and Remove: Carefully unplug the electrical connectors. Then, unbolt the old module from its mounting bracket. Corrosion on the bolts is common, so a little penetrating oil can help.
- Install the New Module: Bolt the new, pre-programmed FPCM into place. Ensure it’s securely mounted.
- Reconnect: Plug the electrical connectors firmly into the new module. You should hear a click.
- Final Step: Reconnect the negative battery terminal. Turn the key to the ‘On’ position for 10 seconds before starting the engine to allow the system to initialize. Your vehicle is ready to go!
Verified Vehicle Compatibility List
This module is a direct replacement for a wide range of GM vehicles. We program it specifically for your VIN to ensure perfect operation. While this is the correct 2008-2009 VUE Fuel Pump Control Module, it also fits the following models:
- ACADIA 2009 (Fuel Pump)
- AVALANCHE 1500 2008-2009 (Fuel Pump; LH frame rail)
- CANYON 2009 (Fuel Pump; rear center frame)
- COLORADO 2009 (Fuel Pump; rear center frame)
- ENCLAVE 2009 (Fuel Pump)
- ESCALADE / ESV / EXT 2008-2009 (Fuel Pump; LH frame rail)
- EXPRESS 1500 VAN 2008-2009 (Fuel Pump; LH frame rail)
- HUMMER H2 2008-2009 (Fuel Pump; LH frame rail)
- HUMMER H3 2009 (Fuel Pump; rear frame)
- OUTLOOK 2009 (Fuel Pump)
- SAVANA 1500 VAN 2008-2009 (Fuel Pump; LH frame rail)
- SIERRA 1500 PICKUP 2007 (New style, smooth door skin), 2008-2009 (Fuel Pump; LH frame rail)
- SIERRA DENALI 2008-2009 (Fuel Pump; LH frame rail)
- SILVERADO 1500 PICKUP 2007 (New style, smooth door skin), 2008-2009 (Fuel Pump; LH frame rail)
- SUBURBAN 1500 2008-2009 (Fuel Pump; LH frame rail)
- TAHOE 2008-2009 (Fuel Pump; LH frame rail)
- TRAVERSE 2009 (Fuel Pump; rear crossmember)
- VUE 2008-2009 (Fuel Pump; RH rear engine compartment)
- YUKON / YUKON XL 1500 2008-2009 (Fuel Pump; LH frame rail)
This part is a direct replacement for part numbers: 13501024, 15213110, 20759945, 20850907, 25785013, 25854536, 25866052, 25967325.
Frequently Asked Questions
Why do I need to provide my VIN?
Your VIN is essential for us to program the module with the correct GM software and calibrations for your specific vehicle. This ensures seamless communication with your car’s computer and proper fuel system operation, making the part truly plug-and-play.
Is this part difficult to install?
No, this is a straightforward installation for most DIYers. Since the programming is already done, it’s a simple unbolt-and-replace job. You just need basic hand tools and about 30-60 minutes.
What happens if I install it without programming?
An unprogrammed module will not work. Your vehicle will likely not start, and you will get communication error codes. Our service eliminates this problem by delivering a module that is ready for installation right out of the box.
Is this a new or used part?
This is a high-quality, tested component that has been loaded with brand new GM software specific to your vehicle. It is guaranteed to restore function to your fuel system.
How do I find the FPCM on my vehicle?
For the Saturn VUE, it’s in the rear passenger side of the engine bay. On most GM trucks and large SUVs (Tahoe, Silverado, etc.), it’s mounted to the frame rail on the driver’s side, typically above the spare tire.