Restore Your HUMMER’s Reliability and Power
Is your 2008-2009 HUMMER H2 experiencing frustrating issues like stalling, hesitating on acceleration, or refusing to start altogether? These are classic signs of a failing Fuel Pump Control Module (FPCM), also known as a Fuel System Control Module (FSCM). This critical component regulates the voltage sent to your fuel pump, ensuring your engine gets the precise amount of fuel it needs. When it fails, it can leave you stranded without warning. In my 20+ years as a technician, I’ve seen countless GM trucks and SUVs sidelined by this exact issue, often after the owner has already replaced a perfectly good fuel pump.
This isn’t just a replacement part; it’s a complete, ready-to-install solution. We take the guesswork and dealership hassle out of the repair. Before we ship your module, we program it with the latest GM software updates specifically for your vehicle using the VIN you provide. This ensures perfect communication with your vehicle’s computer systems and restores original performance and fuel efficiency. Don’t let a faulty module dictate your driving experience. Get the reliable fix with this pre-programmed 2008-2009 HUMMER H2 FPCM.
From the Diagnostic Bay
I remember a 2008 H2 that came into my shop on a tow truck. The owner was convinced his fuel pump was dead for the second time in a year. The engine would crank strong but never fire up. Instead of just throwing another pump at it, I hooked up my scan tool. Sure enough, no communication with the FPCM and a tell-tale code, P069E, was stored. The module, mounted on the frame rail, had succumbed to years of road salt and moisture. We installed one of these pre-programmed modules, and the H2 fired right up on the first try. It’s a 30-minute fix that saves hours of frustration and misdiagnosis.
Key Signs of a Failing FPCM
- ✔ Vehicle cranks but will not start
- ✔ Engine stalls unexpectedly, especially under load
- ✔ Hesitation or stumbling during acceleration
- ✔ “Reduced Engine Power” message on the dash
- ✔ Check Engine Light with diagnostic trouble codes (DTCs) such as P069E, P0230, or U0109
- ✔ Inconsistent fuel pressure readings
A Straightforward Guide to Installation
- ✔ Safety First: Disconnect the negative terminal from your vehicle’s battery to prevent any electrical shorts.
- ✔ Locate the Module: On the HUMMER H2, the FPCM is typically mounted on the driver-side frame rail, near the spare tire. You may need to safely lift and support the vehicle for access.
- ✔ Disconnect and Remove: Unplug the electrical connector(s) from the old module. Then, remove the bolts or nuts securing it to the frame.
- ✔ Install the New Module: Mount your new, pre-programmed FPCM in the same location and secure it with the original hardware.
- ✔ Connect and Finalize: Plug the electrical connector(s) firmly into the new module. Reconnect the negative battery terminal.
- ✔ Start the Engine: Turn the key to the ‘On’ position for 10 seconds to allow the system to prime, then start the engine. It should fire up and run smoothly.
Verified Vehicle Compatibility
This module is a direct-fit replacement for a wide range of GM vehicles. While this listing is for the 2008-2009 HUMMER H2 FPCM, it is also compatible with the following models. It replaces part numbers: 13501024, 15213110, 20759945, 20850907, 25785013, 25854536, 25866052, and 25967325.
- Acadia (2009)
- Avalanche 1500 (2008-2009)
- Canyon / Colorado (2009)
- Enclave (2009)
- Escalade / ESV / EXT (2008-2009)
- Express / Savana 1500 Van (2008-2009)
- HUMMER H2 (2008-2009)
- HUMMER H3 (2009)
- Outlook (2009)
- Sierra / Silverado 1500 (2007 New Body Style, 2008-2009)
- Sierra Denali (2008-2009)
- Suburban 1500 (2008-2009)
- Tahoe (2008-2009)
- Traverse (2009)
- Vue (2008-2009)
- Yukon / Yukon XL 1500 (2008-2009)
Frequently Asked Questions
How do I provide my VIN for programming?
After you complete your purchase, simply send us a message with your 17-digit Vehicle Identification Number (VIN). We will program the module before shipping it to you.
Do I need any special tools to install this?
No special tools are required. Basic hand tools like a socket set and ratchet are all that’s typically needed for this straightforward installation.
Is this part really plug-and-play?
Yes. Because we program it to your specific VIN before shipment, it arrives ready to be installed without any further programming or trips to the dealership.
Where is the FPCM located on my 2008 HUMMER H2?
The Fuel Pump Control Module on the 2008-2009 H2 is typically located on the outside of the driver-side frame rail, often near the spare tire area.
Will this fix a Check Engine Light with code P069E?
Yes, P069E (Fuel Pump Control Module Requested MIL Illumination) is one of the most common codes indicating a failed FPCM. Replacing the module with this programmed unit is the correct repair for that code.