Restore Your Vehicle’s Electrical System with a Plug-and-Play BCM
Are you experiencing a cascade of frustrating electrical problems in your Chevrolet Volt, Buick LaCrosse, or Cadillac SRX? Issues like flickering lights, malfunctioning power windows and locks, a security system that acts up, or even a vehicle that refuses to start can often be traced back to a single, critical component: the Body Control Module (BCM). The BCM is the central command center for your car’s body electronics, and when it fails, it can create chaos. Dealerships often quote astronomical prices for a new module, followed by expensive programming fees. Our BCM programming service offers a reliable and cost-effective solution.
We provide a fully programmed replacement BCM that is a direct-fit solution for your vehicle. By using a specialized cloning process, we transfer all the vital, vehicle-specific data—including VIN, mileage, and key information—from your original module to the replacement unit. This means you receive a part that is truly plug-and-play, eliminating the need for any additional programming or calibration at a dealership. Get your car back to full functionality without the hassle and expense.
From the Diagnostic Bay
A customer brought in their 2015 Chevy Malibu with a list of gremlins that sounded like something out of a horror movie. The dome lights would stay on, the driver’s side window wouldn’t roll down, and the radio would randomly shut off. They had already replaced the battery and checked all the fuses. After connecting our diagnostic scanner, we saw a flood of communication errors all pointing towards the BCM. Instead of a costly new module from the dealer, we recommended our cloning service. We received their original BCM, transferred the data to a replacement unit, and shipped it back. They installed it in under 30 minutes, and every single electrical issue was resolved. It was a simple, effective fix that saved them hundreds of dollars and a lot of headaches.
Is Your 2014-2015 Volt Body Control Module Failing?
A faulty BCM doesn’t always fail completely. It often starts with intermittent, confusing symptoms that can be difficult to diagnose. If you’re noticing any of the following issues, your BCM is the likely culprit.
- ✔ Intermittent or non-functional power windows, door locks, or mirrors.
- ✔ Erratic behavior from interior or exterior lights (flickering, staying on, or not turning on).
- ✔ Malfunctioning windshield wipers or horn.
- ✔ Security system faults or alarm sounding unexpectedly.
- ✔ Dashboard warning lights illuminating without a clear cause.
- ✔ Key fob not working correctly or vehicle not recognizing the key.
- ✔ A no-start condition where the engine cranks but won’t fire up due to security system lock-out.
Our Simple, Hassle-Free Programming Service
Our goal is to make this repair as straightforward as possible. Here’s how our service works:
- Place Your Order: Purchase this BCM service. Ensure your contact information is up-to-date.
- We’ll Contact You: Our team will reach out with clear, step-by-step instructions and a shipping address for you to send your original BCM to us.
- Send Us Your Module: Carefully package and ship your original BCM to our facility.
- We Program Your Replacement: Upon arrival, our technicians will professionally clone all the data from your original module to the replacement unit.
- Receive Your Plug-and-Play BCM: We ship the fully programmed replacement BCM back to you. You’ll receive tracking information once it’s on its way. Installation is as simple as removing the old part and plugging in the new one.
Post-Installation Information
Because we transfer all data, most installations require no further steps. However, in some GM vehicles, specific systems may need to be re-synced after the BCM is replaced. Please be aware of the following potential procedures:
- Airbag System Sync: If the airbag warning light is on after installation, a professional scan tool must be used to perform the ‘Setup SDM Primary Key in BCM’ procedure. This syncs the new BCM with the airbag system.
- Brake Pedal Position Relearn: On some models, a brake pedal position sensor recalibration might be necessary to ensure correct brake light operation and traction control performance.
Disclaimer: Specific procedures can vary by vehicle. We always recommend consulting a factory service manual or a qualified technician for guidance.
Guaranteed Fitment for Your Vehicle
This BCM is a direct replacement for a wide range of General Motors vehicles and part numbers. Please verify that your vehicle and part number are listed below.
This service is compatible with the following part numbers:
13580698, 13578458, 13589115, 13589637, 13590173, 13590851, 13591300, 13592376, 13593775, 13593776, 13594564
This part will fit these makes and models with these options:
- Buick LaCrosse: 2014-2015, 2016 (ID 13580698 or 13594564)
- Buick Regal: 2014-2017
- Cadillac ELR: 2014-2016
- Cadillac SRX: 2014-2016
- Chevrolet Camaro: 2014 (Convertible), 2015
- Chevrolet Malibu: 2014-2015, 2016 (Limited, VIN 1)
- Chevrolet Spark: 2014-2016 (EV model)
- Chevrolet Volt: 2014-2015
Frequently Asked Questions
What is a BCM cloning service?
Our cloning service involves transferring the exact software, VIN, mileage, and security data from your original Body Control Module to a replacement unit. This makes the replacement module a perfect electronic match for your vehicle, avoiding the need for expensive dealership programming.
Why do I need to send my original module to you?
Your original module holds the unique data that is essential for your car to function correctly, including anti-theft and key information. We need it to perform the data transfer (cloning) to the replacement module, ensuring a plug-and-play installation.
Is this BCM truly plug-and-play?
Yes, in over 99% of cases. Because we clone your original data, the vehicle recognizes the replacement BCM as its own. This means no key relearning or security system programming is required. In rare cases, a simple relearn procedure like an airbag sync may be needed, as noted above.
How long does the entire process take?
Once we receive your original module, our programming service is typically completed within 1-2 business days. The total time will depend on shipping times to and from our facility. We ship the programmed module back to you promptly and provide tracking.
Will I need to have my keys reprogrammed?
No. Since we clone the key data from your original BCM, your existing keys will work immediately upon installation without any need for reprogramming.
What if my original BCM is completely dead or not communicating?
In most cases, even if the BCM has failed, we can still extract the necessary data. If you believe your module is severely damaged (e.g., by water or fire), please contact us before ordering to discuss options.