Is Your GM Vehicle Experiencing Bizarre Electrical Problems?
Are your dashboard lights flickering like a disco ball? Do your power windows have a mind of their own? Perhaps your security system is acting up, or the car refuses to start intermittently. These aren’t just random annoyances; they are classic signs of a failing Body Control Module (BCM). The BCM is the central command center for your vehicle’s body electronics, managing everything from interior lighting and power locks to the anti-theft system. When it starts to fail, it can create a cascade of confusing and frustrating issues.
Replacing a BCM isn’t as simple as swapping out a fuse. A new module from the dealership requires expensive and time-consuming programming to sync it with your vehicle’s specific VIN, security keys, and optional features. Our unique programming service eliminates this entire ordeal. We provide a fully functional, tested replacement BCM that is a direct solution for your vehicle, programmed with your original module’s data.
The Simple, Dealership-Free Solution
Our process is designed for simplicity and effectiveness. Instead of towing your car to a dealer and waiting for days, you simply send us your original BCM. Our expert technicians will perform a full data transfer, cloning all the critical information—including VIN, immobilizer data, and vehicle options—onto a replacement module. We then ship the ready-to-install unit back to you. The result is a true plug-and-play solution that restores your vehicle’s functionality without any additional programming required.
From the Diagnostic Bay
We recently had a customer with a 2013 Chevy Equinox whose dashboard would randomly go dark while driving, and the radio would shut off. They had been to two different shops who couldn’t pinpoint the issue, suggesting it might be a complex wiring problem. Suspecting the BCM, they sent their original module to us. We cloned the data to one of our replacement units and sent it back. They installed it in under 30 minutes in their driveway, and every single electrical gremlin vanished. It saved them from what could have been hundreds, if not thousands, in diagnostic fees and dealership programming costs.
Common Symptoms of a Failing BCM
- ✔ Intermittent or non-functional power windows, locks, and mirrors.
- ✔ Erratic behavior from dashboard gauges and warning lights (including check engine, airbag, or security lights).
- ✔ Malfunctioning interior or exterior lights (staying on or not turning on at all).
- ✔ Problems with the keyless entry or remote start system.
- ✔ The anti-theft system engaging incorrectly, leading to a no-start condition.
- ✔ Horn honking unexpectedly or not working at all.
- ✔ Issues with the climate control system.
Why Our Programmed 2013 Volt Body Control Module is the Best Choice
Choosing our service means you are getting a reliable, cost-effective, and straightforward repair. We take all the guesswork and complexity out of the process. The 2013 Volt Body Control Module we provide is meticulously tested and prepared by technicians who specialize in automotive electronics. By cloning your original data, we ensure that the replacement module is a perfect match for your vehicle’s configuration, preserving all factory settings and features.
Installation and Post-Installation Procedures
Installation is typically a direct swap. Locate your old BCM (locations vary by model, see list below), disconnect the battery, unplug the electrical connectors from the old module, remove it, and install the replacement unit in its place. Reconnect the connectors and the battery.
In some cases, minor post-installation procedures may be needed:
- Airbag System Sync: If the airbag warning light is illuminated after installation, a professional scan tool is required to perform the ‘Setup SDM Primary Key in BCM’ procedure. This syncs the new BCM with the airbag system. This is only necessary if the light appears.
- Brake Pedal Position Relearn: Some models may require a brake pedal position sensor recalibration to ensure correct brake light operation and traction control function. This can also be done with a compatible diagnostic tool.
Always consult a factory service manual or a qualified technician for guidance specific to your vehicle.
Guaranteed Compatibility
This BCM is a direct replacement for the following part numbers: 13584695, 13586273, 13580697, 13588447, 13589197, 13589324, 13589325. It is confirmed to fit the following vehicles:
- CHEVROLET CRUZE: 2013 (w/o opt ATH), 2014-2015, 2016 (VIN P, Limited) – Located at LH kick panel.
- CHEVROLET EQUINOX: 2013-2017 – Located at LH side of dash.
- CHEVROLET MALIBU: 2013 – Located at LH kick panel.
- CHEVROLET ORLANDO: 2013-2014 – Located below center console.
- CHEVROLET SPARK: 2014-2015 (gasoline model) – Located at left lower A-pillar.
- CHEVROLET TRAX: 2013-2014 – Located at LH side of dash.
- CHEVROLET VOLT: 2013 – Located in RH engine compartment.
- BUICK ENCORE: 2013-2014 – Located at LH side of dash.
- BUICK REGAL: 2013 – Located at LH dash.
- BUICK VERANO: 2013-2017 – Located below center of dash.
- CADILLAC SRX: 2013 – Located at LH dash.
- GMC TERRAIN: 2013-2017 – Located at LH side of dash.
Frequently Asked Questions
How does the programming service work?
After you place your order, we will contact you with instructions to ship your original BCM to us. Once we receive it, our technicians will transfer all the necessary data to the replacement BCM. We then ship the plug-and-play replacement back to you, typically within 1-2 business days.
Do I need to send my keys with the BCM?
No, you do not need to send your keys. All the necessary key and security information is stored within your original BCM, and we clone that data directly. Your existing keys will work seamlessly with the replacement module.
Is this a guaranteed fix for my vehicle’s problems?
This service corrects issues directly caused by a faulty BCM. While the symptoms listed are common indicators of BCM failure, we always recommend proper vehicle diagnostics to confirm the BCM is the root cause before ordering.
What if my original BCM is completely dead or not communicating?
In many cases, we can still extract the data even from a non-communicating module. Please contact us before ordering if your module is severely damaged (e.g., by water or fire) so we can discuss the likelihood of a successful data recovery.
Do I need to return my old BCM after installation?
No, there is no core charge for this part. You can keep your original module after you receive the programmed replacement from us.