Restore Your Vehicle’s Electrical Stability with a Pre-Programmed BCM
Is your Buick Verano or other GM vehicle acting possessed? Flickering dashboard lights, power windows with a mind of their own, or a security system that prevents your car from starting are all classic signs of a failing Body Control Module (BCM). The BCM is the central command center for your car’s body electronics, managing everything from the interior lights and power locks to the anti-theft system. When it fails, it can cause a cascade of frustrating and unpredictable electrical problems.
Forget the time-consuming and expensive trip to the dealership for programming. We offer a streamlined solution: a professionally prepared BCM that arrives at your door ready for installation. Our service works by cloning the essential data from your original, faulty module onto this replacement unit. This ensures that your vehicle’s specific key codes, VIN, and option settings are perfectly preserved, making the swap as straightforward as possible.
A Technician’s Notebook: The Verano with a Mind of Its Own
A customer brought in a 2015 Verano that was a diagnostic nightmare for another shop. The symptoms were all over the place: the radio would turn off randomly, the turn signals worked intermittently, and sometimes the car just wouldn’t crank. They had already replaced the battery and checked the alternator. When it got to my bay, I suspected the BCM. After locating it below the center of the dash, I disconnected it and took a close look at the board with a magnifying glass. Sure enough, I spotted faint traces of corrosion on two of the pins, likely from a spilled drink long ago. This tiny bit of damage was enough to disrupt communication and cause chaos. A new, properly programmed BCM solved every single issue. This is why our cloning service is so critical—it ensures the new module speaks the exact same language as the rest of your car’s systems.
Is Your Vehicle Exhibiting These BCM Failure Symptoms?
- ✔ Intermittent or non-working power windows, door locks, or mirrors.
- ✔ Erratic interior or exterior lighting (e.g., dome lights staying on, headlights flickering).
- ✔ The security or anti-theft light is on, causing a no-start condition.
- ✔ Dashboard warning lights appearing and disappearing without reason.
- ✔ Communication error codes, often in the U-series (e.g., U0140, U0100), stored in the system.
- ✔ Horn honking unexpectedly or not working at all.
Our Simple, Hassle-Free Cloning Process
Our goal is to get you back on the road quickly and affordably. After your purchase, we will contact you with clear, simple instructions for shipping your original BCM to our facility. Once we receive it, our technicians will perform a full data transfer to the replacement module. We then ship the ready-to-install BCM back to you, typically within 24-48 hours, and provide tracking information. This process for your 2013-2017 Verano BCM eliminates the need for expensive dealer-specific tools.
A Straightforward Guide to Your BCM Installation
- ✔ Safety First: Always disconnect the negative terminal from your vehicle’s battery before starting any electrical work.
- ✔ Locate the Original BCM: On the 2013-2017 Buick Verano, the BCM is located below the center of the dash. For other models, its location varies (see fitment list below). You may need to remove a trim panel for access.
- ✔ Disconnect and Remove: Carefully unplug the electrical connectors from the module. They have locking tabs that need to be depressed. Once disconnected, unbolt or unclip the module from its mounting bracket.
- ✔ Install the Replacement: Mount the new BCM in the same position and securely reconnect all electrical connectors. You should hear a ‘click’ as they lock into place.
- ✔ Reconnect and Test: Reconnect the negative battery terminal. Turn the key to the ‘On’ position and test all body functions—windows, locks, lights, radio, etc.—to confirm proper operation.
Important Post-Installation Information
While our programming service handles the critical vehicle data, some GM vehicles require a ‘handshake’ between modules after installation. Be aware of the following potential procedures:
- Airbag System Sync: If the airbag warning light is illuminated after installation, a professional scan tool is needed to perform the ‘Setup SDM Primary Key in BCM’ procedure. This syncs the new BCM with the airbag system. This is only required if the light is on.
- Brake Pedal Position Relearn: On some models, a brake pedal position sensor relearn may be required to ensure your brake lights and traction control system function correctly.
Disclaimer: Vehicle systems can be complex. We always recommend consulting a factory service manual or a certified technician if you are unsure about any step of the process.
Verified Vehicle Compatibility
This module is a direct replacement for part numbers 13584695, 13586273, 13580697, 13588447, 13589197, 13589324, and 13589325 and fits the following vehicles:
- Buick Verano 2013-2017 (Body Control; below center of dash)
- Buick Encore 2013-2014 (Body Control; LH side of dash)
- Buick Regal 2013 (Body Control; LH dash)
- Cadillac SRX 2013 (Body Control; LH dash)
- Chevrolet Cruze 2013 (Body Control; LH kick panel, w/o opt ATH)
- Chevrolet Cruze 2014-2015 (Body Control; LH kick panel)
- Chevrolet Cruze 2016 (Body Control; LH kick panel, VIN P – Limited)
- Chevrolet Equinox 2013-2017 (Body Control; LH side dash)
- Chevrolet Malibu 2013 (Body Control; LH kick panel)
- Chevrolet Orlando 2013-2014 (Body Control; below center console)
- Chevrolet Spark 2014-2015 (Body Control; left lower a-pillar, gasoline)
- Chevrolet Trax 2013-2014 (Body Control; LH side of dash)
- Chevrolet Volt 2013 (Body Control; RH engine compartment, ID 13580697 or 13586273)
- GMC Terrain 2013-2017 (Body Control; LH side dash)
Frequently Asked Questions
What exactly is this cloning service?
Our cloning service is a process where we transfer the vital vehicle-specific data (like VIN, key information, and security settings) from your original BCM to this replacement unit. This makes the new part plug-and-play, saving you from needing expensive dealer programming.
Do I need to program this 2013-2017 Verano BCM?
No. The entire point of our service is that we handle all the programming for you before we ship the part. It will arrive ready to be installed in your vehicle.
Why do you need my original module?
Your original module holds the unique data that allows it to communicate with the other computers in your car. We need it to extract this data and ensure the replacement module is a perfect electronic match for your specific vehicle.
What happens if my airbag light comes on after installation?
This is a possibility on some GM models. It means the new BCM needs to be electronically introduced to the airbag module. A repair shop with a professional-grade scan tool can perform the ‘Setup SDM Primary Key in BCM’ procedure to resolve this.
Do I need to send my old part back after installation?
No, there is no core charge for this item. You only need to send us your original module for the initial data cloning. You can keep it afterward.
How long does the whole process take?
Once we receive your original BCM, our cloning service typically takes 1-2 business days. We then ship the replacement module back to you. The total time depends on shipping speeds to and from our facility.