Restore Your Vehicle’s Electrical System with a Plug-and-Play Solution
Are you battling frustrating electrical gremlins in your vehicle? Flickering lights, malfunctioning power windows or locks, a security system that acts on its own, or an engine that refuses to start can all point to a single culprit: a failing Body Control Module (BCM). As the central command center for your car’s body electronics, a faulty BCM can cause chaos. This isn’t just an inconvenience; it can be a serious safety issue. This replacement 2011-2013 Caprice BCM, part number 95151084, is the definitive solution to restore order and reliability to your vehicle.
We take the guesswork and high costs out of the repair. Forget expensive dealership visits for programming. With our professional cloning service, you provide us with your vehicle’s VIN, and we flash the module with the latest GM software specific to your car’s configuration. It arrives at your door ready for installation, making this a straightforward repair for a seasoned DIYer or a time-saving solution for any professional mechanic.
A Technician’s Notebook: The Case of the Haunted Impala
I remember a 2012 Impala rolling into my bay with a laundry list of bizarre complaints. The owner said the radio would change stations randomly, the dome light would flicker while driving, and twice the security light had come on, leaving him stranded. He’d already replaced the battery and checked the alternator. My initial scan showed a dozen intermittent communication codes, primarily U-codes pointing to the BCM. Instead of spending hours chasing phantom electrical draws, we opted for a direct approach. We installed a VIN-programmed BCM like this one. The swap took less than an hour, and instantly, every single issue was resolved. It’s a powerful reminder of how this one module can be the root of so many seemingly unrelated problems.
Is Your GM Vehicle Showing These Symptoms?
- ✔ Erratic or non-functional interior/exterior lights.
- ✔ Power windows, door locks, or mirrors working intermittently or not at all.
- ✔ The vehicle’s security system engaging randomly or preventing the car from starting.
- ✔ Horn sounding unexpectedly or not working when pressed.
- ✔ Warning lights on the dash, such as the airbag or ABS light, with no apparent cause.
- ✔ Diagnostic trouble codes (DTCs) related to lost communication, such as U0140, U0155, or other U-series codes.
- ✔ Wipers activating on their own or not turning off.
Your Straightforward BCM Installation Guide
- ✔ Safety First: Always disconnect the negative terminal from your vehicle’s battery and wait a few minutes to ensure all systems are powered down.
- ✔ Locate the BCM: On most compatible vehicles, the BCM is located under the driver’s side dash, often near the steering column or behind a kick panel. Consult your vehicle’s service manual for the exact location.
- ✔ Disconnect and Remove: Carefully unplug the electrical connectors from the old BCM. They have locking tabs that need to be depressed. Once disconnected, unbolt or unclip the module from its mounting bracket.
- ✔ Install the New Module: Mount your new, pre-programmed BCM in the same position as the old one. Securely reconnect all electrical harnesses, ensuring each plug clicks firmly into place.
- ✔ Reconnect and Test: Reconnect the negative battery terminal. Turn the key to the ‘On’ position and test all body functions—lights, locks, windows, wipers, etc.—to confirm the repair was successful.
Important Post-Installation Steps
While our cloning service makes this a near plug-and-play process, some vehicle systems may require a recalibration after the BCM is replaced. Please be aware of the following:
- Airbag System Sync: If your airbag warning light is illuminated after installation, a professional scan tool is needed to perform the ‘Setup SDM Primary Key in BCM’ procedure. This syncs the new BCM with the airbag system.
- Brake Pedal Position Relearn: On certain models, a brake pedal position sensor relearn may be required to ensure correct brake light operation and to prevent issues with the traction control system.
Disclaimer: Vehicle systems vary. Always have a factory service manual available for reference or consult with a qualified automotive technician.
Verified Vehicle Compatibility
This Body Control Module is a direct replacement for part number 95151084 and is interchangeable with a wide range of other GM part numbers. It fits the following vehicles, but always verify your part number and location before ordering:
Fitment: ACADIA 07-12, AVALANCHE 1500 10, CAPRICE 11-13, CAPTIVA SPORT 12, CTS 08-13, DTS 06-11, ENCLAVE 08-12, EQUINOX 07-09, ESCALADE 10, ESCALADE ESV 10, ESCALADE EXT 10, EXPRESS VANS 08-12, G8 08-09, HUMMER H2 08-09, IMPALA 06-13, LUCERNE 06-11, MONTE CARLO 06-07, OUTLOOK 07-10, SAVANA VANS 08-12, SRX 07-09, STS 10, SUBURBAN 1500 10, TAHOE 10, TORRENT 07-09, TRAVERSE 09-12, VUE 08-10, YUKON 10, YUKON XL 1500 10. (Please check the original listing details for specific options and IDs).
Frequently Asked Questions
What is a BCM cloning service?
Our cloning service means we transfer the vital information from your vehicle’s original BCM (using the VIN you provide) to the replacement unit. This ensures it works with your existing keys, security system, and specific vehicle options right out of the box, eliminating the need for further programming.
Why do you need my VIN?
Your Vehicle Identification Number (VIN) is essential for us to program the BCM with the correct software and settings for your exact model, year, and options package. This guarantees compatibility and proper function.
Is this difficult to install myself?
For someone with basic mechanical skills, the physical swap is generally straightforward. The BCM is usually accessible under the dash. Since we handle the programming, you avoid the most complex part of the job. However, we always recommend consulting a service manual.
What happens to my old BCM?
We believe you should keep your original parts. Your original module will always be returned to you along with the programmed replacement unit. We do not keep customer cores.
What if the airbag light comes on after I install it?
This can happen occasionally. It means the new BCM needs to be electronically ‘introduced’ to the airbag control module (SDM). A mechanic with a professional-grade scan tool can perform the ‘Setup SDM Primary Key in BCM’ procedure to resolve this quickly.