Restore Full Functionality to Your GM Vehicle
Are you dealing with perplexing electrical issues in your 2010 Chevrolet Suburban 1500? Problems like erratic power windows, malfunctioning door locks, a flickering security light, or even a no-start condition can often be traced back to a single component: the Body Control Module (BCM). As the central command center for your vehicle’s body electronics, a failing BCM can create a host of frustrating and seemingly unrelated symptoms. This isn’t just an inconvenience; it can affect your vehicle’s security and daily usability.
We offer a straightforward and reliable solution. This is a direct-fit replacement Body Control Module, and the best part is our included Cloning Service. You provide us with your vehicle’s VIN, and we transfer the essential data from your original BCM to this replacement unit. This means no expensive trips to the dealership for programming. The module arrives at your door ready for installation, pre-loaded with the latest GM software updates and your vehicle’s specific configuration.
From the Diagnostic Bay
I remember a customer with a 2010 Tahoe (which uses the same platform as the Suburban) who was ready to sell the truck out of pure frustration. The radio would turn on by itself, the alarm would sound randomly, and the power locks had a mind of their own. He’d replaced the battery and checked fuses, but nothing worked. When we pulled the BCM from under the driver’s side dash, we found faint traces of water staining on the case from a leaky windshield cowl. That moisture intrusion had slowly corroded the internal circuits. A replacement BCM with cloned data had his truck behaving perfectly in under an hour. It’s a reminder that these modules are sensitive, and our service provides a fast path to a complete fix.
Is Your Vehicle Showing These Symptoms?
- ✔ Intermittent or non-working power windows, door locks, or interior lights.
- ✔ The security or anti-theft light stays on, preventing the engine from starting.
- ✔ Dashboard gauges behaving erratically or not working at all.
- ✔ Communication error codes, particularly U-codes like U0140 (Lost Communication With BCM).
- ✔ The key fob is unresponsive or works sporadically.
- ✔ Horn, wipers, or other accessories activating without input.
A Straightforward Guide to Your BCM Installation
Replacing the BCM in your Suburban is a manageable job for a DIYer with basic tools. Our cloning service eliminates the most difficult step—the programming. The module is typically located under the driver’s side dashboard.
- Safety First: Always disconnect the negative terminal from your vehicle’s battery and wait a few minutes before beginning work.
- Locate the BCM: On most 2010 Suburbans, the BCM is located under the steering column, often attached to a larger junction block. You may need to remove a lower dash panel for access.
- Disconnect and Remove: Carefully unplug the multiple wiring harness connectors. They have locking tabs that need to be depressed. Once disconnected, unbolt or unclip the old module and remove it from the vehicle.
- Install the New Module: Mount your new, pre-programmed BCM in the exact same location. Reconnect all wiring harnesses, ensuring each one clicks securely into place.
- Post-Installation Checks: Reconnect the battery terminal. Start the vehicle and test all body functions: lights, locks, windows, radio, etc. Note that some relearn procedures may be necessary as detailed below.
Important Post-Installation Information
While our cloning service makes this a near plug-and-play process, some vehicle systems may require a ‘handshake’ with the new BCM. Please be aware of the following potential procedures:
- Airbag System Sync: If your airbag warning light is illuminated after installation, a professional scan tool is needed to perform the ‘Setup SDM Primary Key in BCM’ procedure. This syncs the airbag system with the new BCM.
- Brake Pedal Position Relearn: On some models, a brake pedal position sensor recalibration may be required to ensure correct brake light and stability control operation.
Disclaimer: Specific procedures can vary by vehicle. Always consult a factory service manual or a qualified technician for guidance.
Verified Vehicle Compatibility
This module is a direct replacement for a wide range of GM vehicles. Please verify your part number or match your vehicle from the list below. This unit replaces part numbers: 10382479, 15093910, 15276271, 15299986, 15819552, and many more.
AVALANCHE 1500 10 Body Control (BCM); (under steering column), ID 25892622
CAPRICE 11-13 Body Control (BCM)
CAPTIVA SPORT 12 Body Control (BCM); (center dash), ID 20921435, 20921436, 22860591
CTS 08-13 Body Control (BCM); LH dash
DTS 06-11 Body Control (BCM); (RH center dash)
ENCLAVE 08-12 Body Control (BCM); (LH dash)
EQUINOX 07-09 Body Control (BCM); (center dash)
ESCALADE 10 Body Control (BCM); (under steering column), ID 20815898 or 25892622
ESCALADE ESV 10 Body Control (BCM); (under steering column), ID 20815898 or 25892622
ESCALADE EXT 10 Body Control (BCM); (under steering column), ID 25892622
EXPRESS/SAVANA VANS 08-12 Body Control (BCM); (center dash)
G8 08-09 Body Control (BCM); (center dash)
HUMMER H2 08-09 Body Control (BCM); (LH firewall)
IMPALA 06-13 Body Control (BCM); (LH dash)
LUCERNE 06-11 Body Control (BCM); (right side dash)
MONTE CARLO 06-07 Body Control (BCM); (LH steering column)
OUTLOOK 07-10 Body Control (BCM); (center dash)
SRX 07-09 Body Control (BCM); LH dash
STS 10 Body Control (BCM); center dash
SUBURBAN 1500 10 Body Control (BCM); (under steering column), ID 20815898 or 25892622
TAHOE 10 Body Control (BCM); (under steering column), ID 20815898 or 25892622
TORRENT 07-09 Body Control (BCM); (center dash)
TRAVERSE 09-12 Body Control (BCM); (LH dash)
VUE 08-10 Body Control (BCM); (center dash)
YUKON 10 Body Control (BCM); (under steering column), ID 20815898 or 25892622
YUKON XL 1500 10 Body Control (BCM); (under steering column), ID 20815898 or 25892622
Frequently Asked Questions
Frequently Asked Questions
What exactly is a ‘Cloning Service’?
Cloning is the process where we transfer the vital vehicle-specific data (like VIN, mileage, and key fob information) from your original BCM to the replacement one. This makes the new module plug-and-play, saving you from a costly and time-consuming programming session at a dealership.
Do I need to send my original BCM to you?
Yes, for the cloning service to be performed, you will need to ship your original module to us after purchase. We will perform the service and ship both your original module and the ready-to-install replacement back to you. We do not keep your original part.
Will this fix my vehicle’s no-start problem?
A faulty BCM is a very common cause of no-start issues related to the anti-theft system. If your security light is on and the engine won’t crank, this part is a very likely solution. However, always perform proper diagnostics, as other issues can cause a no-start condition.
Is this a difficult part to replace myself?
For someone with basic mechanical skills, it is a manageable job. It typically involves removing a plastic panel under the dash and unplugging a few connectors. The main challenge is usually working in a tight space. Our cloning service removes the need for any computer-based work.
What happens if the airbag light comes on after I install it?
This indicates the new BCM needs to be electronically introduced to the airbag system (SDM). This is a simple ‘Setup SDM Primary Key’ procedure that can be done with a bi-directional scan tool, available at most professional repair shops.