Restore Your Jeep’s Performance and Reliability
As a technician with over two decades of experience under the hood, I’ve seen firsthand the frustration a failing Engine Control Module (ECM) can cause. Your 2007-2010 Jeep Patriot, Compass, or Dodge Caliber might be experiencing bizarre, intermittent issues that seem impossible to pin down—from sudden stalling and rough idling to a no-start condition that leaves you stranded. The ECM is the brain of your vehicle’s engine, and when it starts to fail, it can create a cascade of problems. This isn’t just an inconvenience; it’s a matter of reliability and safety. That’s why we offer a straightforward, dependable solution: a professionally programmed 2007-2010 Patriot Engine Computer that gets you back on the road without the dealership hassle or expense.
Forget about costly towing fees, diagnostic dead-ends, and the need for specialized programming tools. We take care of the complex part for you. Simply provide your vehicle’s VIN and mileage during checkout, and we will flash this module specifically for your vehicle. When it arrives at your door, it’s ready for a true Plug-and-Play installation. This direct-fit replacement restores factory performance, smooths out engine operations, and extinguishes that stubborn check engine light for good.
Case Study: A Tricky Diagnosis
I remember a 2009 Patriot that came into the shop. The owner was at his wit’s end. It had an intermittent stalling problem that two other shops couldn’t solve. It would run perfectly for days, then suddenly die at a stoplight. No consistent codes were stored, just a random collection of communication and sensor errors. After checking all the usual suspects—wiring, grounds, fuel pressure—I suspected the ECM. On these vehicles, the ECM can develop internal faults that don’t always throw a clear P0601 or P0606 code. We installed one of our pre-programmed modules, and the problem vanished instantly. The customer called a month later, overjoyed that his Patriot was finally reliable again. It’s a classic example of how a quality 2007-2010 Patriot Engine Computer can be the definitive fix for the most elusive issues.
Is Your Vehicle Showing These Symptoms?
- ✔ Check Engine Light is on with codes like P0601, P0606, or other processor-related faults.
- ✔ The engine cranks but refuses to start.
- ✔ Severe drop in fuel economy for no apparent reason.
- ✔ Intermittent stalling, stumbling, or hesitation while driving.
- ✔ Automatic transmission shifts harshly or erratically.
- ✔ Communication errors with your scan tool (U-codes).
- ✔ Apparent failure of multiple sensors at the same time.
A Straightforward Guide to Installation
- ✔ Safety First: Disconnect the negative terminal from your vehicle’s battery and wait at least 10 minutes to ensure all capacitors are discharged.
- ✔ Locate the ECM: On most 2007-2010 Patriots, Compasses, and Calibers, the engine computer is located in the engine bay, typically mounted to the firewall or inner fender.
- ✔ Disconnect the Harnesses: Carefully release the locking tabs on the electrical connectors and pull them straight out from the module. Avoid pulling on the wires themselves.
- ✔ Remove the Old Module: Unbolt the old ECM from its mounting bracket. There are usually three or four bolts holding it in place.
- ✔ Install the New Module: Mount your new, pre-programmed 2007-2010 Patriot Engine Computer in the same location and secure it with the original bolts.
- ✔ Reconnect Everything: Plug the electrical harnesses firmly back into the new ECM until they click into place. Reconnect the negative battery terminal.
- ✔ Final Step: Start the engine. The vehicle will recognize the new module, and you’re ready to drive. No further programming is required.
Verified Vehicle Compatibility
This engine computer is a guaranteed fit for the following vehicles. Please verify your model and engine options to ensure compatibility. This unit replaces a wide range of part numbers, including 05150471AA, 68043260AB, 04692101AF, and many more listed in the product details.
- ✔ 2007-2010 Jeep Patriot (All engine options)
- ✔ 2007-2010 Jeep Compass (All engine options)
- ✔ 2007-2008 Dodge Caliber (All engine options)
- ✔ 2009 Dodge Caliber (1.8L, 2.0L Gasoline, 2.4L with engine opt ED3)
- ✔ 2010 Dodge Caliber (2.0L, 2.4L)
Frequently Asked Questions
Do I need to do any programming or flashing myself?
Absolutely not. This module arrives fully programmed to your vehicle’s specific VIN and mileage. It is a 100% Plug-and-Play solution, ready for installation right out of the box.
How do you get my vehicle’s information?
During the checkout process, you will be prompted to enter your vehicle’s 17-digit Vehicle Identification Number (VIN) and current mileage. We use this information to program the module correctly.
Will this fix my specific problem?
This ECM is a direct solution for issues caused by a faulty engine computer. If you are experiencing symptoms like a no-start condition, multiple random error codes (especially P0601), or intermittent stalling, a failing ECM is the most likely cause. Proper diagnosis is always recommended.
Is this compatible if my original part number is different?
Yes. This module is compatible with a long list of interchangeable part numbers for this platform. As long as your vehicle is listed in our compatibility chart, this module will function correctly as a replacement, even if the number on your old part is slightly different.
Do I need to send my old part back?
No core charge or return is required for this part, saving you the time and hassle of shipping your old, non-functional module back to us.