Programmed 2007-2010 Outlook BCM | 15921353 Body Control Module

Restore Your Saturn’s Electrical Systems with a Reliable, Programmed BCM

If you’re dealing with baffling electrical issues in your 2007-2010 Saturn Outlook—like power windows with a mind of their own, flickering interior lights, or a security system that randomly acts up—you’ve likely pinpointed the culprit: a failing Body Control Module (BCM). As the central command for your vehicle’s body electronics, a faulty BCM can cause a cascade of frustrating and unpredictable problems. This isn’t just an annoyance; it can affect vehicle security and functionality. We offer a dependable and straightforward solution.

This replacement Body Control Module is meticulously prepared for your vehicle. We take your Vehicle Identification Number (VIN) at the time of purchase and flash the module with the latest, most stable software directly from GM. This means it arrives at your door ready to be installed, saving you from a costly trip to the dealership for programming. You get a reliable part that restores function without the extra hassle and expense. This is the smart, efficient way to get your Outlook back to 100%.

A Technician’s Notebook: The Case of the Wandering Windows

A customer brought in a 2008 Saturn Outlook with a classic BCM failure story. The power door locks worked intermittently, the radio would sometimes not turn off after opening the door, and the driver’s side window would only go down, not up. A scan showed a handful of U-codes, indicating a communication breakdown. In my 20+ years of experience, these specific, unrelated electrical gremlins almost always point back to the BCM. The internal logic circuits and relays fail over time, creating chaos. We installed a VIN-programmed BCM, and instantly, all functions were restored. This is a repair I’ve done hundreds of times on these GM platforms, and a correctly programmed module is the key to a one-time fix.

Key Signs Your BCM is Failing

A faulty BCM can manifest in numerous ways. If your Saturn Outlook is experiencing any of the following, it’s a strong indicator that your module needs replacement. Look out for these common symptoms:

✔ Erratic or non-functional power windows, door locks, or mirrors.
✔ Interior or exterior lights staying on or not turning on at all.
✔ The security system light flashing, or the alarm going off unexpectedly.
✔ Instrument cluster gauges behaving erratically or going dark.
✔ Communication error codes, often in the U-series (e.g., U0140, U0155), indicating the BCM is not talking to other modules.
✔ Remote keyless entry (RKE) failing to work consistently.

Your Straightforward BCM Installation Guide

Installing your new 2007-2010 Outlook BCM is a manageable task for a confident DIYer. For the Saturn Outlook, the BCM is typically located in the center dash area. Always consult a service manual for the exact location on your specific model.

Safety First: Disconnect the negative terminal from your vehicle’s battery and wait at least 10-15 minutes to allow all systems to power down completely.
Locate the BCM: Access the BCM, which is usually found behind the glove box or a lower dash panel on the passenger side. You may need to remove trim panels to get to it.
Disconnect and Remove: Carefully unplug all electrical connectors from the old BCM. Note their orientation. Then, unbolt or unclip the module from its mounting bracket.
Install the New Module: Mount your new, pre-programmed BCM in the same location. Securely reconnect all electrical connectors into their correct ports. Ensure they click into place.
Reconnect Power: Re-attach the negative battery terminal and tighten it securely.
Test and Verify: Turn the key to the ‘On’ position and test all body functions: windows, locks, lights, wipers, and the radio. Start the vehicle to ensure it runs correctly.

Post-Installation Checks & Procedures

Because this module is pre-programmed, most functions should work immediately. However, in some cases, additional vehicle-specific relearn procedures may be needed to sync the new BCM with other systems.

Airbag System Sync: If your airbag/SRS warning light is illuminated after installation, a ‘Setup SDM Primary Key in BCM’ procedure is required. This must be done with a bi-directional scan tool to re-establish communication between the BCM and the airbag module.
Brake Pedal Position Relearn: On some models, a brake pedal position sensor relearn may be necessary to ensure the brake lights and traction control system function correctly. This also typically requires a professional scan tool.

Disclaimer: We offer this information as a guide. Always refer to a factory service manual or a professional technician for procedures specific to your vehicle.

Guaranteed Vehicle Compatibility

This Body Control Module is a direct-fit replacement for a wide range of GM vehicles and is interchangeable with numerous part numbers. We guarantee compatibility for the following models, provided you supply your VIN for programming:

Primary Fitment: Saturn OUTLOOK 2007-2010 (Body Control Module; center dash)

This module also fits these vehicles and replaces these part numbers:
Part Numbers: 10382479, 15093910, 15276271, 15299986, 15819552, 15828601, 15837419, 15872388, 15872421, 15880684, 15921352, 15921353, 15948438, 15948439, 20815898, 20839063, 20864767, 20864768, 20921435, 20921436, 20935349, 22860591, 25826124, 25826125, 25847588, 25847589, 25892622, 25910474, 25934762, 25934763, 95151084
Models: ACADIA 07-12, AVALANCHE 1500 10, CAPRICE 11-13, CAPTIVA SPORT 12, CTS 08-13, DTS 06-11, ENCLAVE 08-12, EQUINOX 07-09, ESCALADE 10, ESCALADE ESV 10, ESCALADE EXT 10, EXPRESS VANS 08-12, G8 08-09, HUMMER H2 08-09, IMPALA 06-13, LUCERNE 06-11, MONTE CARLO 06-07, SAVANA VANS 08-12, SRX 07-09, STS 10, SUBURBAN 1500 10, TAHOE 10, TORRENT 07-09, TRAVERSE 09-12, VUE 08-10, YUKON 10, YUKON XL 1500 10. (Please verify location and specific IDs in fitment data).