Restore Full Functionality to Your Vehicle’s Electronics
Is your Chevrolet Malibu, LaCrosse, or Regal experiencing a host of frustrating and seemingly unrelated electrical problems? Issues like erratic power windows, malfunctioning interior lights, intermittent starting, or warning lights that won’t turn off are often traced back to a single, critical component: the Body Control Module (BCM). The BCM acts as the central nervous system for your vehicle’s body electronics, and when it fails, it can create chaos. This listing offers a straightforward, reliable solution: a replacement Body Control Module, part number 13589637, pre-programmed with your vehicle’s original data.
From the Diagnostic Bay
We once had a 2015 Malibu come in with the owner convinced they needed a new transmission. The gear indicator on the dash was flashing, and it occasionally felt like it was shifting hard. After checking the transmission fluid and running a scan, we found no transmission codes. However, we did see several communication error codes pointing to the BCM. A faulty BCM was sending garbled data across the vehicle’s network, confusing other modules. Instead of a multi-thousand dollar transmission job, a correctly programmed BCM resolved all the issues. It’s a powerful reminder of how a central computer failure can mimic problems in completely different systems.
Symptoms of a Failing Body Control Module
A failing BCM can manifest in numerous ways, often making diagnosis difficult. If you’re experiencing several of the following issues, your BCM is the likely culprit:
- ✔ Unpredictable or non-working power windows, door locks, and mirrors.
- ✔ Interior or exterior lights staying on, flickering, or not working at all.
- ✔ The security system acting up, causing the alarm to go off randomly or preventing the car from starting.
- ✔ Inaccurate or dead gauges on the instrument cluster.
- ✔ Warning lights (like ABS, Airbag, or Check Engine) appearing on the dash without a clear cause.
- ✔ Problems with the keyless entry or remote start system.
- ✔ The radio or climate control system behaving erratically.
Your Plug-and-Play Solution: The 2014-2016 Malibu BCM
Replacing a BCM isn’t as simple as swapping the part. A new module from the dealership requires expensive and complex programming to sync it with your vehicle’s specific VIN, security information, and options. Our unique programming service eliminates this step entirely. We transfer the critical data from your original, failing BCM directly onto this replacement unit. The result is a module that is 100% plug-and-play, requiring no additional work after installation. This saves you time, money, and the hassle of a trip to the dealership.
How Our Programming Service Works:
- ✔ Place Your Order: Complete your purchase for this BCM.
- ✔ We Contact You: We will reach out with clear, simple instructions and a shipping address for you to send us your original BCM.
- ✔ Send Us Your Original Module: Carefully package and ship your vehicle’s original BCM to our facility.
- ✔ We Transfer The Data: Upon receipt, our technicians will professionally clone all necessary data from your old module to the replacement unit.
- ✔ Receive Your Ready-to-Install BCM: We ship the newly programmed BCM back to you, typically within 1-2 business days. You’ll receive tracking information as soon as it’s on its way.
Part Number Compatibility
This module is a direct replacement for a wide range of part numbers. Please verify that your original module has one of the following numbers printed on it:
13580698, 13578458, 13589115, 13589637, 13590173, 13590851, 13591300, 13592376, 13593775, 13593776, 13594564
Verified Vehicle Fitment:
This BCM is confirmed to fit the following vehicles. Please check the specific location notes for your model.
- 2014-2016 Cadillac ELR (RH cowl / RH engine compartment)
- 2014-2016 Chevrolet Spark EV (left lower a-pillar)
- 2014-2016 Cadillac SRX (LH dash)
- 2014-2015 Buick LaCrosse (LH kick panel)
- 2014-2015 Chevrolet Camaro (RH dash)
- 2014-2015 Chevrolet Malibu (LH kick panel)
- 2014-2015 Chevrolet Volt (RH engine compartment)
- 2014-2017 Buick Regal (LH dash)
- 2016 Buick LaCrosse (LH kick panel, ID 13580698 or 13594564)
- 2016 Chevrolet Malibu Limited (VIN 1, LH kick panel)
Important Post-Installation Information
While our goal is a seamless installation, certain vehicle systems may require a recalibration procedure after the BCM is installed. These are standard procedures and can be performed by most professional repair shops with a capable scan tool.
- Airbag System Sync: If the airbag warning light is on after installation, a ‘Setup SDM Primary Key in BCM’ procedure is needed to sync the airbag system with the BCM. This is only necessary if the light appears.
- Brake Pedal Position Relearn: On some models, a brake pedal position sensor recalibration may be required to ensure correct brake light operation and traction control performance.
Disclaimer: Specific procedures can vary by exact make and model. Always consult a factory service manual or a qualified technician for guidance.
Frequently Asked Questions
What is this cloning service and how does it work?
Our cloning service involves transferring the unique, vehicle-specific data (like VIN, mileage, and security keys) from your original BCM to this replacement unit. This makes the replacement module a perfect electronic match for your car, eliminating the need for dealership programming.
Do I need to program this module after I receive it?
No. The module you receive from us will be fully programmed and ready for installation. It is a true plug-and-play solution. In some rare cases, a simple relearn procedure as noted above may be required.
What are the common signs of a failing BCM in my Malibu?
Common symptoms include erratic power windows and locks, dashboard warning lights, non-functional interior lights, and intermittent starting issues. You may experience a combination of these strange electrical problems.
What happens if the airbag light is on after installation?
If the airbag light illuminates, it simply means the airbag module (SDM) needs to be re-synchronized with the BCM. A technician with a professional diagnostic tool can perform the ‘Setup SDM Primary Key in BCM’ procedure to resolve this.
How long does the entire process take?
Once we receive your original module, our programming service typically takes 1-2 business days. The total time will depend on shipping times to and from our facility.
Do I need to send you my keys?
No, you do not need to send us your keys. All the necessary security information is stored within your original BCM, which is all we need for the data transfer.