Restore Your Volt’s Electrical Stability and End Frustrating Glitches
As a technician with over two decades of hands-on diagnostic experience, I’ve seen firsthand how a failing Body Control Module (BCM) can turn a reliable vehicle into a source of constant frustration. If your 2014-2015 Chevrolet Volt is plagued by bizarre electrical issues—like power windows with a mind of their own, flickering lights, a faulty security system, or intermittent starting problems—the BCM is the most likely culprit. It’s the central command center for your car’s body electronics, and when it fails, chaos ensues.
Forget the expensive dealership visit, the towing fees, and the lengthy programming sessions. We offer a streamlined, reliable solution: a replacement BCM programmed with your vehicle’s exact data. This isn’t just a part; it’s a complete fix. By cloning the information from your original module, we deliver a 2014-2015 Volt BCM that is truly plug-and-play, getting you back on the road without the typical dealership hassle.
A Technician’s Notebook: The Volt with a Ghost
A customer brought in a ’14 Volt with a laundry list of complaints: the radio would randomly shut off, the dome light would stay on, and occasionally, the car wouldn’t recognize the key fob. They had been to two other shops that couldn’t find the issue because no hard fault codes were stored. I suspected the BCM was failing internally. Instead of quoting them for a brand new module and hours of programming, we performed a cloning service just like this one. The replacement 2014-2015 Volt BCM went in, and every single ghost in their machine vanished. It’s a powerful fix that saves time, money, and a lot of headaches.
Is Your Volt Showing These Symptoms of BCM Failure?
A faulty BCM can manifest in numerous ways. Check if your vehicle is experiencing any of the following:
- ✔ Erratic or non-functional power windows, door locks, and interior/exterior lights.
- ✔ The security system or alarm sounding randomly or preventing the car from starting.
- ✔ Dashboard warning lights appearing for no reason (e.g., ABS, Airbag, Traction Control).
- ✔ The key fob is not being detected, or remote functions work intermittently.
- ✔ Communication failure codes stored in the system, such as U0140 (Lost Communication With Body Control Module).
- ✔ Complete failure of multiple unrelated electronic accessories at once.
A Straightforward Guide to Installation
Our cloning service makes the physical installation simple. Since the programming is already done, you just need to swap the modules. For the 2014-2015 Volt, your BCM is located in the right-hand (passenger side) of the engine compartment.
- Safety First: Always disconnect the negative terminal from your vehicle’s 12V battery and secure it away from the post to prevent accidental reconnection.
- Locate the BCM: Open the hood and find the BCM in the RH engine compartment. It’s a black box with multiple large electrical connectors.
- Remove the Old Module: Carefully disconnect all electrical connectors. They have locking tabs that need to be pressed or lifted. Once disconnected, unbolt the module from its mounting bracket.
- Install the New Module: Mount your new, pre-programmed BCM in the same location. Securely reconnect all electrical connectors, ensuring they click into place.
- Power Up: Reconnect the negative battery terminal.
- Final Checks: Start the vehicle and test all body functions—windows, locks, lights, radio, etc.—to confirm the repair was successful.
Important Post-Installation Notes
While our goal is a seamless plug-and-play experience, some vehicle systems may require a ‘handshake’ with the new BCM. Please be aware of the following potential procedures:
- Airbag System Sync: If the airbag warning light is illuminated after installation, a professional scan tool is needed to perform the “Setup SDM Primary Key in BCM” procedure. This syncs the airbag system with the BCM.
- Brake Pedal Position Relearn: In some cases, a brake pedal position sensor relearn may be required to ensure correct brake light operation and traction control functionality.
Disclaimer: Specific procedures can vary. We always recommend consulting a factory service manual or a qualified technician for guidance.
Verified Vehicle Compatibility
This BCM is a direct-fit, programmed solution for the following vehicles and part numbers. Please match your part number from the list below to ensure compatibility.
Compatible Part Numbers: 13580698, 13578458, 13589115, 13589637, 13590173, 13590851, 13591300, 13592376, 13593775, 13593776, 13594564
- Chevrolet Volt: 2014-2015 (Body Control (BCM); RH engine compartment)
- Cadillac ELR: 2014-2016 (Body Control (BCM); RH cowl)
- Cadillac SRX: 2014-2016 (Body Control (BCM); LH dash)
- Buick LaCrosse: 2014-2015, 2016 (Body Control (BCM); LH kick panel)
- Buick Regal: 2014-2017 (Body Control (BCM); LH dash)
- Chevrolet Camaro: 2014-2015 (Body Control (BCM); RH dash)
- Chevrolet Malibu: 2014-2015, 2016 (Limited) (Body Control (BCM); LH kick panel)
- Chevrolet Spark EV: 2014-2016 (Body Control (BCM); left lower a-pillar, electric model)
How does the programming service work?
How does the programming service work?
It’s simple! After you place your order, we will contact you with instructions to ship your original BCM to us. Once we receive it, our technicians will extract the vehicle-specific data and transfer it to the replacement module. We then ship the ready-to-install BCM back to you. This process ensures 100% compatibility.
Do I need to send my original BCM? Is there a core charge?
Yes, you must send us your original BCM for the data cloning service. However, there is no core charge, and we will ship your original module back to you along with the newly programmed replacement.
Is this a guaranteed fix for my car’s electrical problems?
This programmed 2014-2015 Volt BCM will resolve any issues directly caused by a faulty Body Control Module. If your vehicle exhibits the common symptoms we’ve listed, it is the most probable solution. However, proper vehicle diagnosis is always recommended to rule out other potential causes like wiring or sensor faults.
What tools do I need for the installation?
Basic hand tools are all that’s required for the physical swap: typically a socket set to remove the module’s mounting bolts and a small flathead screwdriver to help with connector tabs if they are stiff. No special programming tools are needed on your end.