Tired of Chasing Electrical Gremlins in Your Camaro?
As a technician with over two decades of experience, I’ve seen firsthand how a failing Body Control Module (BCM) can turn a great car into a source of constant frustration. If your 2014-2015 Camaro is experiencing bizarre issues like power windows acting up, random warning lights, malfunctioning door locks, or even a no-start condition, the BCM is the likely culprit. This module is the central nervous system for your vehicle’s body electronics, and when it fails, it creates chaos. Finding a fix can be a nightmare of expensive diagnostic fees and dealer-only programming requirements—until now.
We offer a simple, reliable solution: a replacement BCM that arrives at your door fully programmed and ready for installation. Our service eliminates the need for a trip to the dealership. Here’s how it works: you purchase this module, and we’ll provide instructions for shipping your original BCM to our facility. Our expert technicians will then transfer all the critical vehicle-specific data—like your VIN, mileage, and key information—to this replacement unit. The result is a true plug-and-play 2014-2015 Camaro BCM, perfectly synced to your car.
A Technician’s Notebook: The Case of the Phantom Drain
A customer brought in a ’15 Camaro with a battery that would die overnight. We checked everything—alternator, battery, starter—all tested fine. There were no obvious lights left on. After hooking up an ammeter, we saw a significant parasitic draw. The culprit? The BCM wasn’t telling other modules to go to ‘sleep’ after the key was off. It was keeping the radio and instrument cluster partially active, slowly draining the battery. A simple swap with one of our programmed BCMs solved the issue instantly, saving the customer from what would have been hours of costly wiring diagnostics.
Common Signs of a Failing BCM
A faulty BCM can cause a wide range of symptoms that often seem unrelated. If you’re noticing any of the following, it’s time to consider a replacement:
- ✔ Intermittent or non-working power windows, door locks, or interior lights.
- ✔ Security system faults or the anti-theft light staying on.
- ✔ Inaccurate fuel gauge readings or erratic instrument cluster behavior.
- ✔ Communication error codes, such as U0140, U0155, or other ‘U’ codes indicating a loss of communication.
- ✔ The engine cranks but refuses to start due to the BCM not recognizing the key.
- ✔ Unresponsive key fob or remote start functions.
Your Straightforward BCM Installation Guide
Installing your pre-programmed BCM is a manageable task for a confident DIYer. For the 2014-2015 Camaro, the BCM is typically located behind the right-hand side of the dashboard.
- Step 1: Safety First. Always disconnect the negative terminal from your vehicle’s battery before beginning any electrical work.
- Step 2: Access the Module. You will likely need to remove the glove box or a lower dash panel on the passenger side to gain access to the BCM.
- Step 3: Disconnect and Remove. Carefully unplug the electrical connectors from the old BCM. They have locking tabs that need to be depressed. Once disconnected, unbolt the module from its mounting bracket.
- Step 4: Install the New BCM. Mount your new, programmed BCM in the same location and securely reconnect all the electrical harnesses. Ensure they click into place.
- Step 5: Reassemble and Reconnect. Reinstall any panels you removed and reconnect the negative battery terminal.
- Step 6: Final Checks. Start the vehicle and test all body functions—windows, locks, lights, radio, etc.—to confirm proper operation. Refer to the post-installation notes below if any warning lights appear.
Important Post-Installation Information
While our programming service makes this a plug-and-play solution, some vehicle systems may require a quick recalibration after the new module is installed.
- Airbag System Sync: In some cases, the airbag warning light may illuminate after installation. This is not a fault with the part, but a security handshake that needs to be reset. A professional scan tool is required to perform the ‘Setup SDM Primary Key in BCM’ procedure to sync the modules.
- Brake Pedal Position Relearn: To ensure proper brake light and traction control operation, a brake pedal position sensor relearn might be necessary. This can also be done with a capable diagnostic tool.
Disclaimer: Procedures can vary. Always consult a factory service manual or a qualified technician if you are unsure about any step.
Verified Fitment For These GM Vehicles
This BCM, part number 13592376, is a direct replacement for several part numbers and fits a variety of GM models. Please verify your original part number is on this list: 13580698, 13578458, 13589115, 13589637, 13590173, 13590851, 13591300, 13593775, 13593776, 13594564.
- Buick LaCrosse: 2014-2016
- Buick Regal: 2014-2017
- Cadillac ELR: 2014-2016
- Cadillac SRX: 2014-2016
- Chevrolet Camaro: 2014-2015
- Chevrolet Malibu: 2014-2016 (including Limited)
- Chevrolet Spark EV: 2014-2016
- Chevrolet Volt: 2014-2015
Frequently Asked Questions About Our BCM Service
How does the programming service work?
How does the programming service work?
After you place your order, we will contact you with simple, prepaid shipping instructions to send us your original BCM. Once we receive it, we transfer its unique data to the replacement module and ship it back to you, usually within 1-2 business days. This cloning process ensures 100% compatibility with your vehicle’s existing systems.
Do I need to send my keys?
How does the programming service work?
After you place your order, we will contact you with simple, prepaid shipping instructions to send us your original BCM. Once we receive it, we transfer its unique data to the replacement module and ship it back to you, usually within 1-2 business days. This cloning process ensures 100% compatibility with your vehicle’s existing systems.
Is this a guaranteed fix for my car’s problems?
How does the programming service work?
After you place your order, we will contact you with simple, prepaid shipping instructions to send us your original BCM. Once we receive it, we transfer its unique data to the replacement module and ship it back to you, usually within 1-2 business days. This cloning process ensures 100% compatibility with your vehicle’s existing systems.
What is your policy on core charges?
How does the programming service work?
After you place your order, we will contact you with simple, prepaid shipping instructions to send us your original BCM. Once we receive it, we transfer its unique data to the replacement module and ship it back to you, usually within 1-2 business days. This cloning process ensures 100% compatibility with your vehicle’s existing systems.
What if my original BCM is completely dead or not communicating?
How does the programming service work?
After you place your order, we will contact you with simple, prepaid shipping instructions to send us your original BCM. Once we receive it, we transfer its unique data to the replacement module and ship it back to you, usually within 1-2 business days. This cloning process ensures 100% compatibility with your vehicle’s existing systems.