Is Your 2010 Yukon Acting Possessed? You’re Not Alone.
If you’re dealing with a frustrating mix of electrical gremlins in your 2010 GMC Yukon—like flickering dashboard lights, power windows with a mind of their own, a radio that’s gone silent, or a security system that randomly prevents the truck from starting—the culprit is almost certainly a failing Body Control Module (BCM). As the central computer for your vehicle’s comfort and convenience features, when the BCM goes, it takes a lot of essential functions with it. This isn’t just an annoyance; it’s a critical failure that can leave you stranded.
The Dealership-Free Solution: A Pre-Programmed BCM
Forget about towing your Yukon to the dealership and facing a hefty bill for diagnostics, parts, and programming. We offer a direct, reliable solution. This Body Control Module, part number 25910474, arrives at your door completely pre-programmed to your vehicle’s specific VIN. We load it with the latest, most stable software updates from GM, ensuring it communicates flawlessly with your Yukon’s other systems right out of the box. This is the fix you need to restore order to your vehicle’s electronics.
Expert Pro Tip: Check This Before You Order
In my 20+ years as a technician, I’ve seen countless BCMs replaced when the real issue was a poor ground connection. Before you finalize your order, take 10 minutes to locate the main BCM ground wire (on the GMT900 platform, it’s typically a black wire bolted to the chassis near the driver-side A-pillar kick panel). Unbolt it, clean the contact point and the terminal with a wire brush until they’re shiny, and re-tighten it securely. In about 10% of cases, this simple step can resolve the issue. If your problems persist, you can be confident the BCM itself is the fault.
Key Features & Benefits of This 2010 Yukon Body Control Module
- ✔ VIN-Specific Programming Included: Simply provide your VIN at checkout, and we handle all the programming. No extra tools or subscriptions needed.
- ✔ Eliminates Common Failures: Solves issues like erratic interior/exterior lights, malfunctioning power locks and windows, dead radio/infotainment, and security-related no-start problems.
- ✔ Latest GM Software: We flash the module with the most current GM updates, which often correct factory bugs and improve performance.
- ✔ Broad Compatibility: This single module is a direct replacement for a wide range of original part numbers, ensuring a perfect match.
- ✔ Save Time and Money: By skipping the dealership’s programming service, you save hundreds of dollars and get your truck back on the road faster.
Simple Installation Process
Installing your new BCM is a straightforward process for a DIYer with basic tools. The BCM on your 2010 Yukon is located under the driver’s side of the dashboard, near the steering column.
- Safety First: Always disconnect the negative terminal from your vehicle’s battery and wait 10 minutes before beginning.
- Access the Module: Remove the lower dash panel beneath the steering wheel to gain access to the BCM.
- Disconnect and Remove: Carefully unplug the electrical connectors. They have locking tabs that need to be depressed. Once disconnected, unbolt the old BCM from its mounting bracket.
- Install the New BCM: Mount your new, pre-programmed BCM in place and securely reconnect all electrical connectors. You should hear a ‘click’ as they lock in.
- Reconnect Battery: Re-attach the negative battery terminal.
Important Post-Installation Steps
After installing your new 2010 Yukon Body Control Module, a couple of final procedures are required to ensure full system integration and safety. These steps require a professional-grade diagnostic scan tool.
- Airbag System Reset: To clear the airbag warning light, you must perform the ‘Setup SDM Primary Key in BCM’ procedure. This re-establishes the security handshake between the new BCM and the airbag system’s Sensing and Diagnostic Module (SDM).
- Brake Pedal Position Sensor Relearn: Some vehicles will require a brake pedal position sensor relearn or recalibration. This is crucial for the proper function of the brake lights, traction control, and stability control systems.
If you are not equipped or comfortable with performing these procedures, we strongly recommend seeking assistance from a qualified local mechanic.
Guaranteed Fitment for Part Number 25910474 and Its Alternatives:
This module replaces the following part numbers: 10382479, 15093910, 15276271, 15299986, 15819552, 15828601, 15837419, 15872388, 15872421, 15880684, 15921352, 15921353, 15948438, 15948439, 20815898, 20839063, 20864767, 20864768, 20921435, 20921436, 20935349, 22860591, 25826124, 25826125, 25847588, 25847589, 25892622, 25934762, 25934763, 95151084.