2009 Envoy Engine Control Module Programmed ECM 12625453

Restore Your Envoy’s Performance!

Fix stalling, rough idle, and check engine lights with this pre-programmed Engine Control Module. It’s flashed to your vehicle’s VIN with the latest GM software, so no dealer visit is needed. A true plug-and-play solution! Get back on the road fastโ€”order today!

$149.95

+11.99 USPS Priority Shipping

Availability: In stock



SKU: 590-01536-25 Categories: ,
Guaranteed Safe Checkout

Is Your GM Truck or SUV Acting Up? It Could Be the ECM.

As a mechanic with over two decades of experience under the hood, I’ve seen it all. When a vehicle like a 2009 GMC Envoy, a Trailblazer, or even a Cadillac STS starts acting erraticallyโ€”stalling for no reason, poor fuel economy, a persistent check engine light, or a dreaded no-start conditionโ€”the root cause is often the Engine Control Module (ECM). This component is the brain of your engine, and when it fails, it can create a diagnostic nightmare. You might be chasing phantom sensor codes or replacing perfectly good parts, all because the central computer is malfunctioning.

The Smart Solution: A VIN-Programmed 2009 Envoy Engine Control Module

Forget the hassle and expense of a dealership visit. This Engine Control Module is the direct, effective solution you’ve been looking for. We take the guesswork out of the repair by pre-programming this unit specifically for your vehicle using your VIN. This isn’t just a generic part; it’s a component loaded with the latest, most stable software updates directly from GM. This ensures that when you receive it, it’s ready to communicate perfectly with your vehicle’s specific systems, from the transmission to the anti-lock brakes.

A Mechanic’s Real-World Experience

“A customer’s 2009 Trailblazer with the 6.0L V8 came into my shop last week with these exact symptoms. The owner was frustrated, having already replaced the throttle body and a couple of O2 sensors with no luck. The scanner showed intermittent communication loss and a P0606 ‘ECM Processor Fault’ code. We confirmed the wiring was solid, pointing directly to an internal ECM failure. Instead of a costly dealer part and programming fee, we installed one of these VIN-programmed modules. The entire job took less than 30 minutes, the codes cleared, and the truck ran smoother than it had in years. This is the same reliable fix you’re getting here.”

Key Benefits of This Programmed ECM:

  • โœ” VIN-Specific Programming: We flash the module with your vehicle’s VIN and the newest GM software for flawless compatibility.
  • โœ” No Dealer Required: This module is a true plug-and-play solution, saving you hundreds in dealership programming fees.
  • โœ” Resolves Common Issues: Effectively corrects problems like rough idle, stalling, check engine lights (CEL), and communication errors.
  • โœ” Broad Compatibility: This single unit is a direct replacement for multiple service numbers, ensuring a perfect match.

Simple, DIY-Friendly Installation Guide

You don’t need to be a master technician to install this part. Follow these simple steps to get your vehicle back in top shape.

  1. Safety First: Always disconnect the negative terminal from your vehicle’s battery and wait about 10 minutes to ensure all systems are powered down.
  2. Locate the ECM: On the 2009 Envoy, the ECM is typically found on the driver’s side of the engine compartment, near the firewall. Its location may vary on other compatible models (e.g., behind the firewall on a Colorado/Canyon).
  3. Disconnect the Old Module: Carefully release the locking tabs on the electrical connectors and pull them straight out. Avoid wiggling them side-to-side to prevent pin damage. Unbolt the old module from its mounting bracket.
  4. Install the New Module: Bolt the new ECM into place. Firmly press the electrical connectors into their sockets until you hear and feel them click securely.
  5. Final Step: Reconnect the negative battery terminal. The vehicle may need to run for a few minutes to complete its internal relearn procedures.

Guaranteed Fitment & Interchangeability

This module is a direct replacement for a wide range of GM vehicles and is interchangeable with the following part numbers: 12636659, 12639300, 1263605, 12628993, 12628911, 12625453, 12622175, 12630464, and 12678512.

It is confirmed to fit the following vehicles (and more):

  • 2009 GMC Envoy (5.3L)
  • 2009-2012 Chevrolet Colorado / GMC Canyon (2.9L, 3.7L)
  • 2009 Chevrolet Trailblazer (6.0L)
  • 2009-2010 Hummer H3 (3.7L)
  • 2009 Cadillac CTS (6.2L), SRX (4.6L), STS (4.4L, 4.6L), XLR
  • 2009-2011 Cadillac DTS & Buick Lucerne (4.6L)
  • 2009 Chevrolet Corvette (ZR1)
  • 2009 Saab 9-7X

IMPORTANT: Please provide your vehicle’s 17-digit VIN at checkout to ensure we can program the module for your exact configuration before shipping.

Genuine OEM

Yes

MPN

12625453

Interchange part number

Condition

Refurbished

PartNumber

590

Model

ENVOY

Make

Year

2009

Brand

CHEVROLET TRUCK

Manufacturer Part Number

, , , , , , , ,

GTIN

Does not apply

Scroll to Top