Restore Peak Performance to Your 3.7L Jeep
Is your 2009-2010 Jeep Commander or Grand Cherokee suffering from frustrating and unpredictable engine issues? Symptoms like a persistent check engine light, sudden stalling, rough idling, or a complete no-start condition often point directly to a failing Engine Control Module (ECM). The ECM is the central computer of your vehicle, responsible for managing everything from fuel injection and ignition timing to transmission shifting and emissions control. When it begins to fail, it can create a cascade of problems that are difficult to diagnose and can leave your reliable Jeep sidelined.
This replacement Engine Control Module, part number 68028162, is the definitive solution to restore your vehicle’s original performance and reliability. Unlike a generic part from a local store, this ECM arrives at your door fully programmed to your vehicle’s specific Vehicle Identification Number (VIN) and mileage. This critical step ensures complete compatibility and a true Plug-and-Play installation, eliminating the need for an expensive trip to the dealership for programming or flashing. You can get your Jeep back on the road quickly and confidently.
From the Diagnostic Bay
We had a 2009 Grand Cherokee 3.7L come into the shop that was a real head-scratcher. The owner had already replaced the crankshaft position sensor, camshaft sensor, and two O2 sensors trying to chase down an intermittent stalling issue and a handful of confusing diagnostic codes. The vehicle would run fine for days, then suddenly die at a stoplight. After hours of checking wiring harnesses and grounds, we finally focused on the ECM. We swapped in a known-good programmed module, and the Jeep fired up and ran perfectly. The original ECM had an internal fault that would only appear when it reached a certain temperature, causing it to send erratic signals. It’s a classic case where throwing parts at a problem costs more time and money than correctly identifying the faulty computer from the start.
Common Symptoms of a Failing Jeep ECM
- ✔ Persistent Check Engine Light (CEL) that won’t clear or returns immediately.
- ✔ Engine misfires, stumbles, or runs rough, especially under load.
- ✔ Vehicle refuses to start or has difficulty starting (hard starting).
- ✔ Unexplained and significant drop in fuel economy.
- ✔ Automatic transmission shifts erratically, harshly, or gets stuck in gear.
- ✔ Communication errors with diagnostic scan tools or other vehicle modules.
- ✔ Stalling for no apparent reason while driving or at idle.
Why This 2009-2010 Jeep Commander ECM is Your Best Solution
Choosing the right part is crucial for a lasting repair. This module is meticulously inspected and programmed to meet or exceed original factory specifications. By providing us with your VIN during checkout, you ensure that the software loaded onto the module is the correct calibration for your Jeep’s specific options and emissions equipment. This tailored programming is what makes the installation process so seamless. Simply disconnect the battery, swap the old module with this new one, reconnect the battery, and start your engine. No specialized tools, no dealer appointments, no hassle.
This module is a direct replacement for a wide range of original part numbers, ensuring broad compatibility for the 3.7L engine in both the Commander and Grand Cherokee platforms for the 2009 and 2010 model years. Please verify your part number against the comprehensive list below to confirm fitment.
Direct Fit For:
- 2009-2010 Jeep Commander with 3.7L Engine (Located in RH engine compartment)
- 2009-2010 Jeep Grand Cherokee with 3.7L Engine (Located in RH rear engine compartment)
Compatible Part Numbers:
05150467AA, 05150467AB, 68028166AB, 68028166AC, 68028166AD, 68028166AE, 68028166AF, 68060531AB, 68060531AC, 68060531AD, 68059198AA, 68059198AB, 68028167AB, 68028167AC, 68028167AD, 68028167AE, 68028162, 68059197, 68028163, 68028154, 68059196, 68028155, 68028155AD, 68028150, 68059195, 68028151, 68028174, 68028175, 68028176
Frequently Asked Questions
Is this ECM really “Plug & Play”?
Absolutely. We program the module using your vehicle’s VIN, which loads the correct software and security information. This allows you to install it without any additional programming required from a dealer or mechanic.
Where is the ECM located on my 2009 Jeep Commander?
On the 2009-2010 Jeep Commander, the Electronic Control Module is located in the engine compartment on the right-hand (passenger) side, typically near the firewall.
Do I need to send my old computer back?
For this specific part, there is typically no core charge or requirement to return your old module. You can recycle it locally. Please double-check the specific product page details at the time of purchase.
Will this fix my check engine light?
If the check engine light is caused by an internal failure of the ECM, then this part will resolve the issue. However, if the light is on due to a faulty sensor, wiring, or other mechanical problem, those issues will need to be addressed separately.
What information do you need from me to program it?
To ensure perfect compatibility, we require your vehicle’s 17-digit Vehicle Identification Number (VIN) and the current mileage. You can typically find the VIN on your driver’s side dashboard (visible through the windshield) or on your vehicle’s registration.
Is this compatible with my 2010 Grand Cherokee 3.7L?
Yes, this ECM is a direct fit for the 2009-2010 Jeep Grand Cherokee equipped with the 3.7L V6 engine. The mounting location is slightly different (RH rear of the engine compartment), but the module and its programming are fully compatible.