2009-2010 Commander ECM Engine Computer 68059198AB

Restore Your Jeep’s Performance Instantly!

Get your 2009-2010 Commander or Grand Cherokee back on the road with our plug-and-play engine computer. Pre-programmed to your VIN, it requires no dealer visit for installation. Fix stalling, misfires, and check engine lights today. Order now for a fast, reliable solution!

$199.95

+11.99 USPS Priority Shipping

Out of stock

Guaranteed Safe Checkout

Is Your Jeep Commander or Grand Cherokee Acting Up? The ECM Might Be the Culprit.

If your 2009-2010 Jeep Commander or Grand Cherokee with the 3.7L V6 engine is experiencing frustrating issues like erratic idling, stalling, a persistent Check Engine Light, or even a no-start condition, the root cause is often a failing Engine Control Module (ECM). The ECM is the brain of your vehicle’s engine, controlling everything from fuel injection and ignition timing to emissions systems and transmission shifting. When it begins to fail, it can create a cascade of problems that are difficult to diagnose and can leave you stranded. Don’t let a faulty computer dictate your vehicle’s reliability. This direct-fit replacement ECM is the definitive solution to restore your Jeep’s performance and dependability.

From the Diagnostic Bay

We had a 2010 Grand Cherokee 3.7L come into the shop that was a real head-scratcher. The owner complained of intermittent stalling at stoplights and a random cylinder misfire code (P0300) that would come and go. We checked the plugs, coils, and fuel injectors – all were fine. The wiring harness showed no signs of damage. After hours of chasing ghosts, we hooked up a scope to the injector control signals coming from the ECM. We found that the signal for cylinder 3 would drop out intermittently, just for a millisecond, but it was enough to cause the misfire and stall. A new, properly programmed ECM like this one solved the problem instantly. The owner was thrilled to have his reliable Jeep back, and it was a great reminder that sometimes the most complex problems have a straightforward, if not obvious, solution.

Symptoms of a Failing 2009-2010 Commander ECM

A failing engine computer can manifest in numerous ways. If you’re experiencing any of the following, it’s a strong indicator that your ECM needs attention. Look out for:

  • ✔ Check Engine Light: The light is on, and you may have codes related to sensors, misfires, or internal module failure (like P0600-P0606).
  • ✔ Engine Stalling or Misfiring: The engine may stall unexpectedly, run rough, or misfire, especially under load or when idling.
  • ✔ No-Start Condition: The engine cranks but refuses to start. This can happen if the ECM isn’t properly controlling the fuel or spark.
  • ✔ Poor Fuel Economy: A faulty ECM can’t efficiently manage the engine’s fuel delivery, leading to a noticeable drop in MPG.
  • ✔ Inconsistent Performance: You might notice a sudden loss of power, hesitation during acceleration, or other unpredictable engine behavior.
  • ✔ Transmission Shifting Issues: The ECM communicates with the transmission controller, so a bad module can cause harsh shifting, or the vehicle may not shift out of a specific gear.
  • ✔ Communication Errors: Your mechanic’s scan tool may be unable to communicate with the ECM, a definitive sign of an internal failure.

The Plug-and-Play Advantage: No Dealer Required

The biggest hurdle in replacing an engine computer has always been the programming. Traditionally, you would have to buy the part, install it, and then have your vehicle towed to a dealership for expensive flashing and key relearning procedures. Our process eliminates that entirely. This 2009-2010 Commander ECM arrives at your door fully programmed to your vehicle’s specific Vehicle Identification Number (VIN) and current mileage. This ensures that all factory settings, anti-theft information, and engine parameters are perfectly matched to your Jeep.

The result is a true Plug-and-Play installation. Simply disconnect the battery, swap the old module with the new one, reconnect the battery, and start your engine. There are no additional programming tools or trips to the dealer needed. This saves you hundreds of dollars in labor and towing fees and gets you back on the road in under an hour.

Simple Installation Steps:

  1. Safety First: Disconnect the negative terminal from your vehicle’s battery.
  2. Locate the ECM: On the 2009-2010 Commander and Grand Cherokee 3.7L, the ECM is typically located in the engine compartment on the right-hand (passenger) side.
  3. Disconnect Connectors: Carefully unplug the electrical wiring harnesses connected to the old ECM. There are usually locking tabs that need to be released.
  4. Remove the Old Module: Unbolt the old ECM from its mounting bracket.
  5. Install the New Module: Mount your new, pre-programmed ECM in the same location and secure it with the bolts.
  6. Reconnect Everything: Plug the wiring harnesses firmly into the new ECM until they click into place. Reconnect the negative battery terminal.
  7. Start Your Vehicle: Your Jeep should now start and run smoothly with its performance and reliability restored.

Guaranteed Compatibility

This engine control module is a direct replacement for a wide range of original part numbers. Please verify that your existing module’s part number is on this list to ensure perfect fitment:

Compatible Part Numbers: 05150467AA, 05150467AB, 68028166AB, 68028166AC, 68028166AD, 68028166AE, 68028166AF, 68060531AB, 68060531AC, 68060531AD, 68059198AA, 68059198AB, 68028167AB, 68028167AC, 68028167AD, 68028167AE, 68028162, 68059197, 68028163, 68028154, 68059196, 68028155, 68028155AD, 68028150, 68059195, 68028151, 68028174, 68028175, 68028176

Frequently Asked Questions

Do I need to do any programming or flashing myself?

Absolutely not. This ECM comes fully pre-programmed to your vehicle’s VIN. The process is 100% Plug-and-Play. Once you install it, you are ready to start the engine and drive.

What information do you need from me to program the module?

After you place your order, we will need your vehicle’s 17-digit VIN (Vehicle Identification Number) and the current mileage. This ensures a perfect software match for your Jeep’s specific configuration.

Will this fix my specific problem?

This module will correct any issue directly caused by a faulty ECM. While the symptoms listed above are strong indicators, we always recommend a proper diagnosis by a qualified mechanic to confirm the ECM is the point of failure before ordering.

Is this compatible with both the Commander and the Grand Cherokee?

Yes, this ECM is compatible with both the 2009-2010 Jeep Commander and the 2009-2010 Jeep Grand Cherokee, as long as the vehicle is equipped with the 3.7L V6 engine.

Do I need to have my keys reprogrammed?

No. Our programming process includes syncing the module to your vehicle’s existing anti-theft system information, which is derived from your VIN. Your current keys will work just as they did before.

Condition

Refurbished

Year
Genuine OEM

Yes

MPN

68059198AB

Interchange part number

PartNumber

590

Model

COMMANDER

Year

2009

Brand

Chrysler

Manufacturer Part Number

, , , , , , , , , , , , , , , , , , , , , , , , , , ,

Scroll to Top