2008 Isuzu I-370 Engine Control Module ECM 12630457

Restore Your Truck’s Performance!

Get your 2008 Isuzu I-370 running smoothly again with our VIN-programmed engine control module. This direct-fit ECM arrives ready to install, solving frustrating issues like poor performance and check engine lights. Order today for a reliable fix!

$141.74

+11.99 USPS Priority Shipping

Availability: In stock



SKU: 590-08112-217 Categories: ,
Guaranteed Safe Checkout

Restore Peak Performance to Your Isuzu Truck

Is your 2008 Isuzu I-370 suffering from perplexing issues like a persistent check engine light, poor fuel economy, stalling, or rough idling? The Engine Control Module (ECM) is the central computer of your vehicle, orchestrating critical functions like fuel delivery, ignition timing, and emissions control. When it begins to fail, it can cause a cascade of problems that are often difficult to diagnose. This replacement Engine Control Module, part number 12630457, is the definitive solution to restore your truck’s reliability and performance.

From the Diagnostic Bay
We had a 2008 Isuzu I-370 in the shop that was driving the owner crazy. It had an intermittent no-start condition and would occasionally stall at stoplights. Previous mechanics had replaced the crank sensor and fuel pump, but the problem persisted. After hooking up our diagnostic scanner and monitoring live data, we noticed that the 5-volt reference signal to several key sensors would drop out randomly. This wasn’t a sensor or wiring issue; the voltage drop was originating inside the ECM itself. We installed one of our VIN-programmed modules, performed the security relearn, and the truck has been running flawlessly ever since. It’s a classic case of a failing internal component in the ECM causing ghost-like symptoms.

Common Symptoms of a Failing ECM

A faulty ECM can manifest in various ways. If you’re experiencing any of the following, your engine’s computer could be the culprit. It’s crucial to properly diagnose the issue, but these symptoms are strong indicators of a module problem.

  • ✔ Persistent Check Engine Light (CEL) with various trouble codes.
  • ✔ Engine misfires, stumbles, or runs rough.
  • ✔ Unexplained drop in fuel efficiency.
  • ✔ Vehicle fails to start or has difficulty starting.
  • ✔ Intermittent stalling, especially when warm or at idle.
  • ✔ Poor acceleration or loss of power.
  • ✔ Automatic transmission shifting issues or harsh shifts.
  • ✔ Communication errors when trying to use a diagnostic scan tool.

The Right Solution: A VIN-Programmed 2008 Isuzu I-370 Engine Control Module

Don’t settle for a generic, unprogrammed module that will require expensive dealership visits. Our process ensures you receive a part that is a perfect match for your vehicle’s specific configuration. When you order this 2008 Isuzu I-370 Engine Control Module, we flash it with the latest GM-certified software updates using the Vehicle Identification Number (VIN) you provide. This critical step ensures that all systems communicate correctly, from the engine and transmission to the anti-lock brakes and security system. This module is a direct replacement for service number 12630457 and is also interchangeable with several other part numbers, including 12590032, 12602044, 12603530, and more, ensuring wide compatibility across many GM platforms.

Installation and Setup

On the 2008 Isuzu I-370, the ECM is conveniently located on the right-hand (passenger side) of the firewall in the engine bay. Installation is straightforward for a DIY mechanic with basic tools. After disconnecting the battery, simply unplug the electrical connectors, unbolt the old module, and install the new one. Once installed and the battery is reconnected, you may need to perform a vehicle security relearn procedure (often called a Passlock relearn). This procedure pairs the new ECM to your vehicle’s anti-theft system and can typically be done without special tools in under 30 minutes. Instructions for this procedure are widely available online or in your vehicle’s service manual.

Frequently Asked Questions

Do I need to get this module programmed by a dealer?

No. We handle the programming for you before we ship the part. Simply provide us with your vehicle’s VIN during or after checkout, and it will arrive ready for installation, flashed with the latest software for your specific truck.

Where is the ECM located on my 2008 Isuzu I-370?

The Engine Control Module is located in the engine compartment, mounted to the firewall on the right-hand (passenger) side.

Is installation difficult? Will I need special tools?

Installation is straightforward and requires only basic hand tools to unbolt the old unit and install the new one. However, you will likely need to perform a security relearn procedure, which pairs the new ECM to your vehicle’s anti-theft system. This can usually be done without any special tools.

How do I provide my VIN?

After you complete your purchase, you can send us your 17-digit VIN by replying to your order confirmation email or through our website’s contact form. We cannot ship your part until we receive your VIN.

My current module has a different part number. Will this still work?

This module is a direct replacement for several service numbers. Please check the list of compatible numbers on this page, including 12590032, 12602044, 12603530, 12605843, 12607096, 12630457, and 19210737. If your number is on this list, this part will work for your vehicle.

Genuine OEM

Yes

Year
Condition

Refurbished

MPN

12630457

Interchange part number

PartNumber

590

Model

isuzu-i-370

Year

2009

Brand

GM

Manufacturer Part Number

, , , , ,

Hardware Type

Scroll to Top