2008-2010 Vue Engine Control Module 12590032 | Programmed to Your VIN

End Your Vue’s Engine Problems.

Tired of stalling, a lit check engine light, or poor performance in your 2008-2010 Saturn Vue? This Engine Control Module is your solution. It arrives pre-programmed to your vehicle’s VIN with the latest GM software, eliminating the need for a costly dealership visit. It’s a direct-fit, reliable fix for a wide range of engine management issues. Provide your VIN at checkout and get back on the road with confidence!

$118.99

+11.99 USPS Priority Shipping

Availability: In stock



SKU: 590-08112-53 Categories: ,
Guaranteed Safe Checkout

Restore Peak Performance to Your Saturn Vue

Is your 2008-2010 Saturn Vue experiencing frustrating issues like stalling, erratic shifting, a persistent check engine light, or even a no-start condition? These are classic signs of a failing Engine Control Module (ECM), the computer that acts as the brain of your vehicle’s engine. A faulty ECM can disrupt everything from fuel delivery and ignition timing to transmission performance, making your vehicle unreliable and unsafe. Don’t let a bad module keep you off the road or force you into an expensive dealership visit.

This is your direct, hassle-free solution. We offer a reliable replacement 2008-2010 Vue Engine Control Module that arrives at your door pre-programmed to your vehicle’s specific Vehicle Identification Number (VIN). This critical service, performed by our expert technicians before shipping, ensures the module communicates flawlessly with your Vue’s other systems right out of the box. You get the latest GM software updates without needing any specialized tools or a trip to the dealer for programming. It’s the most efficient way to get your vehicle running smoothly again.

From the Diagnostic Bay: The Intermittent No-Start Mystery

A customer brought in a 2009 Saturn Vue 3.6L that would randomly refuse to start. No crank, no click—just silence. Other times, it would start and run perfectly. They had already replaced the battery and starter to no avail. After hooking up my scanner, I found intermittent communication loss codes (U0100) stored in other modules. In my 20+ years of experience, when you see ghost-like electrical problems that don’t have a clear mechanical cause, the ECM is a primary suspect. We tested the power and ground circuits to the ECM, which were solid. The culprit was the ECM itself, with an internal fault causing it to intermittently fail. A replacement 2008-2010 Vue Engine Control Module, pre-programmed with the customer’s VIN, solved the problem in under an hour. It’s a fix I’ve done hundreds of times, and it saves customers time, money, and a lot of diagnostic headaches.

Is Your Vue Showing These Telltale Signs?

A failing ECM can manifest in numerous ways. If you’re noticing any of the following, it’s time to consider a replacement:

  • ✔ Unexplained Check Engine Light (CEL) illumination
  • ✔ Stored diagnostic trouble codes (DTCs) like P0601, P0606, or U0100
  • ✔ Engine stalling, stumbling, or hesitating during acceleration
  • ✔ Rough or inconsistent idling
  • ✔ Vehicle won’t start, or starts intermittently
  • ✔ Noticeable decrease in fuel economy
  • ✔ Harsh or erratic automatic transmission shifting

Your Straightforward Installation Guide

Installing your new ECM is a manageable job for a DIYer with basic tools. Follow these steps for a successful replacement.

  1. Safety First: Disconnect the negative terminal from your vehicle’s battery and secure it away from the post to prevent accidental reconnection.
  2. Locate the ECM: On the 2008-2010 Saturn Vue, the Engine Control Module is typically located in the engine compartment. Depending on the engine, it can be on the firewall or near the fan shroud.
  3. Disconnect the Wiring: Carefully unplug the electrical connectors from the old module. There are usually release tabs that need to be pressed or lifted. Do not force them.
  4. Remove the Old Module: Unbolt the old ECM from its mounting bracket. Keep the mounting hardware, as you will need it for the new unit.
  5. Install the New Module: Mount your new, pre-programmed ECM using the original hardware. Reconnect the electrical connectors, ensuring they click securely into place.
  6. Reconnect the Battery: Re-attach the negative battery terminal.
  7. Perform Security Relearn: Your vehicle may require a security relearn procedure to recognize the new ECM. This typically involves turning the key to the ‘ON’ position for 10-15 minutes, then off, and repeating two more times before starting the engine. Consult your owner’s manual for the specific procedure for your vehicle.

Verified Compatibility for Your Vehicle

This ECM is a direct replacement for service number 12590032 and is also interchangeable with part numbers 12602044, 12603530, 12605843, 12607096, 12630457, and 19210737. It fits a wide range of GM vehicles, including the following Saturn Vue models:

  • ✔ 2008-2009 Saturn Vue: Fits 2.4L models with VIN Z (8th digit, opt LAT).
  • ✔ 2008 Saturn Vue: Fits 3.6L models.
  • ✔ 2009 Saturn Vue: Fits 3.6L models with VIN 7 (8th digit, opt LY7).
  • ✔ 2010 Saturn Vue: Fits 3.6L models.

Please use the comprehensive fitment list above to verify compatibility with other GM makes and models. Matching your original part number is the best way to guarantee fitment.

Frequently Asked Questions

Do I need to program this module?

No. We handle the programming for you before we ship. Simply provide your vehicle’s VIN at checkout, and the module will arrive ready for installation with the latest GM software.

What is a VIN and where do I find it?

The VIN is your 17-digit Vehicle Identification Number. You can find it on your vehicle’s registration, insurance card, or on a small plate on the driver’s side of the dashboard, visible through the windshield.

Will this fix my check engine light?

If the check engine light is caused by a faulty ECM (e.g., codes P0601, P0606), this replacement part will resolve the issue. However, you must ensure the ECM is the true cause of the problem and that there are no other underlying issues.

Is this part difficult to install?

For someone with basic mechanical skills, this is a straightforward installation. It involves disconnecting the battery, unplugging connectors, and swapping the module. The most important step is the security relearn procedure after installation.

What happens if I don’t provide my VIN?

We cannot ship the module without your VIN. The programming process is essential for the part to function correctly in your specific vehicle. We will contact you after your purchase to obtain this information.

Genuine OEM

Yes

Condition

Refurbished

MPN

12590032

Interchange part number

PartNumber

590

Model

VUE

Year

2009

Brand

GM

Manufacturer Part Number

, , , , ,

Hardware Type

Scroll to Top