Is Your Dodge Avenger, Sebring, or Journey Acting Up?
There’s nothing more frustrating than a vehicle that won’t run right. If your 2008, 2009, or 2010 Dodge Avenger, Sebring, or Journey with the 2.4L engine is experiencing perplexing issues like stalling, a persistent check engine light, or a no-start condition, the root of the problem is often the Engine Control Module (ECM). As the central computer of your vehicle, the ECM is responsible for managing everything from fuel injection and ignition timing to transmission shifting. When it fails, it can cause a cascade of problems that are often difficult to diagnose.
Don’t let a faulty computer keep you off the road or lead to expensive, unnecessary repairs. We offer a reliable, direct-fit solution with this pre-programmed Engine Control Module. It’s designed to restore your vehicle’s performance and get you back behind the wheel with confidence, eliminating the need for a costly trip to the dealership for programming.
From the Diagnostic Bay
I once had a 2009 Dodge Journey with the 2.4L engine come into the shop with a very strange, intermittent no-start condition. The battery was good, the starter tested fine, and all the fuses were intact. The owner had already replaced the starter to no avail. We could never get it to fail consistently in the bay. After hours of tracing wiring diagrams, we noticed the fault only happened after the engine had been running for a while. On a hunch, we used a heat gun to gently warm up the ECM, and the no-start condition appeared instantly. A hairline fracture on the circuit board was expanding when hot, breaking a critical connection. Swapping in a quality replacement ECM like this one solved the problem immediately. It’s a reminder that not all ECM failures throw obvious codes.
Common Symptoms of a Failing ECM
- ✔ Persistent Check Engine Light (CEL) that won’t clear, often with communication-related fault codes (U-codes).
- ✔ Engine misfires, stumbles, or runs rough, especially under load.
- ✔ The vehicle cranks but refuses to start.
- ✔ Unexplained and sudden decrease in fuel efficiency.
- ✔ Erratic or harsh shifting from the automatic transmission.
- ✔ Intermittent stalling, either while driving or at idle.
- ✔ Loss of power and poor acceleration.
- ✔ Cooling fans running constantly, even when the engine is cold.
The Perfect Solution: A Pre-Programmed 2008-2010 Avenger ECM
Our key advantage is the pre-programming service. Before this module ships, we flash it with your vehicle’s specific Vehicle Identification Number (VIN) and current mileage. This ensures that the computer is perfectly synced with your car’s factory settings, including the anti-theft system (immobilizer). The result is a true Plug & Play installation. You simply disconnect the old module and connect this one. There are no additional programming fees, no special tools required, and no trip to the dealership necessary.
Guaranteed Fitment and Part Number Compatibility
This Engine Control Module is a direct replacement for 2.4L equipped models of the following vehicles:
- 2008-2010 Dodge Avenger
- 2008-2010 Chrysler Sebring
- 2009-2010 Dodge Journey
This unit is compatible with and replaces a wide range of original part numbers. Please verify that your original part number is on this list to ensure proper fitment:
Compatible Part Numbers: 05150472AA, 05150518AA, 68046281AA, 68046281AB, 68046281AC, 68046281AD, 68046282AA, 68046282AB, 05187273AD, 68046282AC, 68046282AD, 05187273AA, 05187273AB, 05187273AC, 05187274AA, 05187274AD, 05187271AA, 05187272, 05187265, 05187266, 05187263, 05187267, 05187269, 05187270, 05187254, 05187255, 05187861, 05187251, 05187991, 05187252, 05187992, 05187250, 05187990, 05187237, 05187243, 05187236, 05187862, 05187239, 05187233, 05187240, 05187232, 05187238, 05187249
Frequently Asked Questions
Do I need to program this module?
No. This ECM comes fully programmed to your vehicle’s VIN. It is a complete plug-and-play solution, requiring no further programming from a dealer or mechanic.
Where do I provide my VIN and mileage?
You will be prompted to enter your vehicle’s VIN and mileage during the checkout process. This information is essential for us to program the module correctly before shipping.
Is this a brand new part?
This is a high-quality, fully tested replacement part that meets or exceeds original equipment specifications. Each unit undergoes rigorous testing to ensure reliability and performance.
What if my original part number isn’t on the compatibility list?
If your part number is not listed, please contact us with your vehicle’s VIN before ordering. We can verify compatibility to ensure you receive the correct part for your car.
Will this fix my check engine light?
If the check engine light is caused by a faulty ECM, this replacement will resolve the issue. It’s important to have a proper diagnosis to confirm the ECM is the source of the problem before ordering.
Is any special ‘relearn’ procedure needed after installation?
Generally, no special procedures are required. The vehicle will adapt to the new module within a few drive cycles. In some cases, a simple idle relearn procedure (letting the car idle for a few minutes) may be beneficial.