2007-2012 Acadia BCM 20815898 Programmed Body Control Module

End Your Acadia’s Electrical Nightmares

Solve frustrating issues like flickering lights, faulty power locks, and no-start problems with this reliable Body Control Module for your 2007-2012 GMC Acadia. We program it to your vehicle’s specific VIN, so it arrives ready for a straightforward installation, saving you a costly trip to the dealership. Restore your vehicle’s proper function and peace of mind. Order today for a simple, effective fix!

$224.95

+11.99 USPS Priority Shipping

Availability: In stock



SKU: 591-01465-748 Categories: ,
Guaranteed Safe Checkout

Tired of Electrical Gremlins in Your GMC Acadia?

As a technician with over two decades of experience under the hood, I’ve seen it all. If your 2007-2012 GMC Acadia is starting to act haunted—with flickering dashboard lights, power windows with a mind of their own, or a security system that randomly prevents you from starting the engine—the culprit is very often a failing Body Control Module (BCM). This isn’t just an annoyance; it’s the central command center for your vehicle’s comfort and convenience features. When it falters, it can make your daily drive a frustrating ordeal.

This isn’t a part you can just grab off a shelf and install. A new BCM from a dealership requires expensive programming and calibration. We take that entire burden off your shoulders. This replacement 2007-2012 Acadia BCM arrives at your door pre-programmed with the latest GM software, specifically matched to your vehicle’s VIN. It’s a direct, effective solution designed to restore your vehicle’s functionality without the dealership price tag or wait times.

Case Study: A Tricky Diagnosis

I remember a 2011 Acadia that came into my shop with a truly baffling set of symptoms. The owner complained of intermittent radio failure, the dome light staying on, and the liftgate refusing to open. They had already replaced the battery and checked fuses, but the problems persisted. A quick scan showed a dozen communication codes (U-codes), all pointing to network chaos. Instead of spending hours tracing wires, my experience pointed directly to the BCM. After installing a VIN-programmed module like this one, every single electrical issue vanished. It’s a prime example of how this single component can be the root of widespread, seemingly unrelated problems.

Common Signs of a Failing BCM

If your vehicle is exhibiting any of these symptoms, a faulty BCM is the likely cause. Replacing it can be the definitive fix you’re looking for.

  • ✔ Erratic or non-functional power windows, door locks, and mirrors.
  • ✔ Interior or exterior lights that flicker, stay on, or don’t work at all.
  • ✔ The security system light flashing, preventing the vehicle from starting (Pass-Key/Passlock issues).
  • ✔ Instrument cluster gauges behaving erratically or going dark.
  • ✔ Communication error codes, such as U0140, on a diagnostic scan.
  • ✔ Wipers or horn activating unexpectedly.
  • ✔ Remote keyless entry (fob) failing to work consistently.

A Straightforward Guide to Installation

For the handy DIYer or professional mechanic, swapping the BCM in your Acadia is a manageable job. The BCM is located on the left-hand (driver’s side) of the dashboard, typically behind the lower dash panel.

  1. Safety First: Always disconnect the negative terminal from your vehicle’s battery and wait a few minutes to ensure all systems are powered down.
  2. Access the Module: Carefully remove the lower dash panel beneath the steering column to expose the BCM. It’s a black box with several large electrical connectors.
  3. Disconnect and Remove: Photograph the connector layout for reference. Then, carefully release the locking tabs on each electrical connector and unplug them. Remove the mounting bolts or clips holding the old BCM in place and take it out.
  4. Install the New BCM: Mount your new, pre-programmed BCM in the same location. Reconnect all the electrical connectors firmly until they click into place.
  5. Final Steps: Reinstall the dash panel and reconnect the negative battery terminal. Start the vehicle to confirm that the primary issues are resolved.

Important Post-Installation Note: In some cases, additional relearn procedures may be necessary. For instance, if the airbag light is on, a professional scan tool is needed to perform the ‘Setup SDM Primary Key in BCM’ procedure. A Brake Pedal Position relearn might also be required for proper traction control function. Always refer to a factory service manual for model-specific details.

Verified Vehicle Compatibility

This Body Control Module, part number 20815898, is a direct replacement for a wide range of General Motors vehicles. While this listing is focused on the 2007-2012 Acadia BCM, it also fits many other models including the Buick Enclave, Chevy Traverse, Saturn Outlook, and various Cadillac, Chevrolet, and GMC trucks and vans. We program it specifically for the VIN you provide, ensuring perfect compatibility. This module replaces numerous original part numbers, including 15921352, 25826124, 25934762, and many more.

Do I need to do any programming myself?
No. We handle all the programming before we ship the module. Simply provide your vehicle’s VIN during checkout, and it will arrive ready for installation. This saves you a trip to the dealer.

Is there a core charge for my old part?
Absolutely not. You can keep your old module, so there’s no need to worry about the cost or hassle of sending a core back to us.

Where is the BCM located on my 2009 GMC Acadia?
On the 2007-2012 GMC Acadia, the Body Control Module is located on the driver’s side, behind the lower part of the dashboard, near the steering column.

What if my airbag light comes on after installation?
This can happen occasionally. It means the new BCM needs to be synced with the airbag’s Sensing and Diagnostic Module (SDM). This requires a ‘Setup SDM Primary Key’ procedure using a professional-grade scan tool. A local repair shop can typically perform this for you.

Will this fix my vehicle’s no-start problem?
If the no-start is caused by the anti-theft system (a common BCM failure), then yes, this programmed module is the correct solution. It restores communication and allows the engine to start.

Genuine OEM

Yes

Condition

Refurbished

MPN

20815898

Interchange part number

PartNumber

591

Model

ACADIA

Year

2013

Brand

GM

Manufacturer Part Number

, , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Scroll to Top