2007-2010 Patriot Engine Computer 68043260AA | Programmed to Your VIN

Restore Your Patriot’s Performance

Get your 2007-2010 Jeep Patriot running right again with this plug-and-play engine computer. It arrives fully programmed to your VIN and mileage, eliminating the need for expensive dealer visits. Fix stalling, rough idle, and check engine lights. Fix your issue today!

$159.95

+11.99 USPS Priority Shipping

Availability: Only 1 left in stock



SKU: 590-01761-47 Categories: ,
Guaranteed Safe Checkout

Is Your Jeep Patriot Stalling, Misfiring, or Refusing to Start?

As a mechanic with over two decades of experience, I’ve seen countless Jeep Patriots, Compasses, and Dodge Calibers roll into the shop with baffling electrical issues. The owner is frustrated, the check engine light is glaring, and the vehicle is completely unreliable. Often, the root cause isn’t a simple sensor or a bad wireโ€”it’s a failing Engine Control Module (ECM), the brain of your vehicle’s engine management system.

When the ECM starts to go, it can cause a cascade of problems that seem unrelated, from poor fuel economy and rough idling to a complete no-start condition. You’re not just losing your transportation; you’re losing peace of mind. The thought of a costly dealership visit for diagnostics and programming is enough to cause a headache on its own.

The Plug-and-Play Solution You’ve Been Searching For

This is where our pre-programmed ECM, part number 68043260AA, comes in. We take the guesswork and the dealership out of the equation. Before we ship it, we flash the module with your vehicle’s specific VIN and current mileage. The result? A true plug-and-play component that is ready for installation the moment it arrives at your door. No expensive scan tools, no subscription fees, and no need to have your vehicle towed for programming.

“A customer’s 2009 Patriot came in last week with intermittent stalling and a persistent P0606 code (Internal Control Module Processor Error). After spending an hour verifying the wiring harness and grounds were solidโ€”a critical first stepโ€”we knew the original ECM was the culprit. Swapping in a pre-programmed unit like this one had him back on the road in under 30 minutes, without a tow to the dealer. The relief on his face was immediate.”

Why Choose Our 2007-2010 Patriot Engine Computer?

Getting your vehicle back to factory-spec performance is our top priority. This module is the definitive fix for a wide range of common issues. When you choose our ECM, you’re getting a reliable, tested part that solves the problem correctly the first time.

  • โœ” No Additional Programming Required: We handle all the flashing in-house. It arrives ready to install, saving you hundreds of dollars in dealership fees.
  • โœ” VIN & Mileage Specific: Your vehicle’s unique data is loaded onto the module, ensuring seamless communication with the other systems in your Jeep or Dodge.
  • โœ” Fixes Common Failure Symptoms: Effectively resolves issues like random stalling, engine misfires, harsh shifting, no-start conditions, and persistent diagnostic trouble codes (DTCs) that won’t clear.
  • โœ” Broad Compatibility: This single module is a direct replacement for a wide range of part numbers, ensuring a perfect match for your vehicle.

Simple Installation Guide: Get Back on the Road Fast

You don’t need to be a master technician to install this part. With basic hand tools and about 30-60 minutes, you can complete this job in your own driveway.

  1. Safety First: Disconnect the negative terminal from your vehicle’s battery and wait at least 10 minutes to allow all systems to discharge.
  2. Locate the ECM: On the 2007-2010 Patriot, the ECM is typically located in the engine bay, on the driver’s side, near the firewall or strut tower.
  3. Disconnect the Connectors: Carefully unclip the two large electrical harness connectors from the old ECM. Inspect the pins on both the harness and the new module for any corrosion or damage. Clean them with an electrical contact cleaner if necessary.
  4. Remove the Old Module: Unbolt the old ECM from its mounting bracket. It’s usually held in place by a few 8mm or 10mm bolts.
  5. Install the New ECM: Mount the new, pre-programmed ECM onto the bracket and securely fasten the bolts.
  6. Reconnect and Secure: Plug the electrical connectors firmly into the new module until they click into place. Reconnect the negative battery terminal.
  7. Final Check: Turn the key to the ‘ON’ position (without starting) for 30 seconds, then turn it off. Repeat this cycle three times to allow the systems to sync. Then, start your engine. Your check engine light should be off, and your vehicle should run smoothly.

Guaranteed Fitment & Part Number Compatibility

This engine computer is a direct-fit replacement for the 2007-2010 Jeep Patriot, 2007-2010 Jeep Compass, and various 2007-2010 Dodge Caliber models. It is fully compatible with the following OEM part numbers:

05150471AA, 05150523AA, 68043260AA, 68043260AB, 04692101AD, 04692101AE, 04692101AF, 68043260AC, 68043260AD, 68043261AC, 68043261AA, 68043261AB, 68070011AA, 68071022AA, 05033359AJ, 05187817AF, 68000107AF, 68026147AA, 68026147AC, 68028201AA, 68028201AC, 68028205AB, 68044228AA.

Condition

Refurbished

Genuine OEM

Yes

MPN

68043260aa

Interchange part number

PartNumber

590

Model

PATRIOT

Year

2007

Brand

Chrysler

Manufacturer Part Number

, , , , , , , , , , , , , , , , , , , , , , ,

Scroll to Top