2007-2010 Compass Engine Computer 68028205AB Programmed Plug & Play

End Frustrating Engine Problems

Get your Jeep Compass, Patriot, or Dodge Caliber running smoothly again with this fully programmed engine computer. It arrives flashed to your VIN for a simple, Plug & Play installation that requires no dealer visit. This is the definitive fix for common issues like stalling, no-starts, and false check engine lights. Restore your vehicle’s reliability and performance. Order today for a fast, hassle-free repair!

$159.95

+11.99 USPS Priority Shipping

Availability: Only 1 left in stock



SKU: 590-01761-43 Categories: ,
Guaranteed Safe Checkout

Restore Your Vehicle’s Performance and Reliability

If you’re dealing with frustrating and unpredictable issues like your 2007-2010 Jeep Compass, Patriot, or Dodge Caliber stalling, running rough, or simply refusing to start, a failing Engine Control Module (ECM) is often the culprit. I’ve seen it countless times in my 20+ years in the shop: what seems like a major mechanical failure is actually a communication breakdown in the vehicle’s electronic brain. This replacement 2007-2010 Compass Engine Computer is the definitive solution, arriving at your door fully programmed to your vehicle’s specific VIN and mileage for a true Plug & Play installation.

Forget about expensive dealership visits, towing fees, and the headache of coordinating programming. We handle the complex part for you. Simply provide your VIN during checkout, and our experts will flash the module with the correct software for your exact vehicle configuration. This ensures all components, from the transmission to the fuel injectors, operate exactly as the factory intended, restoring smooth performance and fuel efficiency.

A Technician’s Notebook: The Phantom Stall

A customer brought in a 2009 Dodge Caliber with a problem that was driving them crazy. The car would run perfectly for days, then suddenly stall at a stoplight with no warning and no immediate check engine light. They had already replaced the spark plugs and a camshaft sensor at another shop, with no luck. After hooking up my high-end scanner, I noticed intermittent communication loss with the PCM (U0100). On a hunch, I gently wiggled the main connector on the ECM, and the engine sputtered. This confirmed my suspicion: internal circuit board failure. We installed a pre-programmed ECM just like this one, and the phantom stalling issue was gone for good. It’s a classic case where the central computer is the root cause of seemingly unrelated symptoms.

Is Your Vehicle Showing These Symptoms?

A failing ECM can manifest in various ways, often mimicking other component failures. If you’re experiencing any of the following, this module is the likely solution for your 2007-2010 Compass Engine Computer issues.

  • ✔ Check Engine Light is on with communication-related Diagnostic Trouble Codes (DTCs) like P0600, P0601, or U0100.
  • ✔ The engine cranks but refuses to start.
  • ✔ Unexplained stalling or rough idling, especially after the vehicle has warmed up.
  • ✔ A noticeable decrease in fuel economy.
  • ✔ Harsh or erratic automatic transmission shifting.
  • ✔ Issues with other electronic systems, as the ECM is the central communication hub.

Your Straightforward Installation Guide

Installing your new engine computer is a job most DIY mechanics can handle in under an hour with basic hand tools. This process avoids the need for specialized diagnostic equipment or dealer programming.

  1. Safety First: Always disconnect the negative terminal from your vehicle’s battery and wait at least 10 minutes for any residual power to dissipate.
  2. Locate the ECM: On most Compass, Patriot, and Caliber models, the ECM is located in the engine bay, typically mounted to the firewall or inner fender.
  3. Disconnect the Connectors: Carefully release the locking tabs on the main wiring harness connectors and pull them straight off the module. Avoid pulling on the wires themselves.
  4. Remove the Old Module: Unbolt the old ECM from its mounting bracket. There are usually 3 or 4 bolts holding it in place.
  5. Install the New Module: Mount your new, pre-programmed ECM onto the bracket and secure the bolts.
  6. Reconnect Everything: Firmly press the wiring harness connectors back into the new module until they click into place. Reconnect your negative battery terminal.
  7. Final Step: Start the vehicle and let it idle for a few minutes to allow the electronic systems to fully sync. Your repair is complete!

Verified Vehicle Compatibility

This ECM is a direct-fit replacement for a wide range of vehicles, ensuring seamless integration. It is compatible with part numbers 05150471AA, 05150523AA, 68043260AA, 68043260AB, and many more. Please verify your vehicle is on the list below to ensure proper fitment.

  • Jeep Compass: 2007, 2008, 2009, 2010 (Electronic Control Module)
  • Jeep Patriot: 2007, 2008, 2009, 2010 (Electronic Control Module)
  • Dodge Caliber: 2007, 2008 (Electronic Control Module)
  • Dodge Caliber: 2009 (1.8L, 2.0L Gasoline, 2.4L with engine opt ED3)
  • Dodge Caliber: 2010 (2.0L, 2.4L)

This is the reliable, cost-effective way to get your vehicle back on the road and running like new. Order your programmed 2007-2010 Compass Engine Computer today and solve those persistent electronic issues for good.

Frequently Asked Questions

Do I need to do any programming myself?

No. This engine computer comes fully programmed to your vehicle’s VIN and mileage. It is a true Plug & Play solution, ready for installation right out of the box.

Where do I provide my VIN?

You can enter your vehicle’s 17-digit VIN during the checkout process. This is crucial for us to program the module correctly for your specific car.

Is this compatible with other part numbers?

Yes, this unit replaces a long list of original part numbers, including 68043260AA, 04692101AF, 68028201AC, and 68028205AB among others. Please see the full list in the description.

What tools are needed for installation?

You’ll typically only need basic hand tools, such as a socket set or wrench to disconnect the battery and remove the mounting bolts for the module.

Will this fix my ‘no-start’ problem?

If your ‘no-start’ condition is caused by a faulty ECM (often indicated by a lack of communication or specific DTCs), then this part is the correct fix. It’s one of the most common reasons for this symptom in these vehicles.

How long does installation take?

For someone with basic mechanical skills, the entire process of swapping the module should take less than an hour.

Condition

Refurbished

Genuine OEM

Yes

MPN

68028205ab

Interchange part number

PartNumber

590

Model

COMPASS

Year

2007

Brand

Chrysler

Manufacturer Part Number

, , , , , , , , , , , , , , , , , , , , , , ,

Scroll to Top