Restore Peak Performance to Your Vehicle
Is your Dodge Caliber, Jeep Patriot, or Jeep Compass suffering from frustrating and unpredictable issues? Problems like a persistent check engine light, sudden stalling, rough idling, or a complete no-start condition often point to a failing Engine Control Module (ECM). The ECM is the central brain of your vehicle, orchestrating everything from fuel injection and ignition timing to emissions control and transmission shifting. When it falters, the entire system’s reliability is compromised. This replacement Engine Control Module, part number 68043260AB, is the definitive solution to restore your vehicle’s factory performance and dependability.
The Simple, No-Hassle Solution: Plug & Play Installation
We take the guesswork and complexity out of ECM replacement. Forget about expensive dealership visits, towing fees, and the need for specialized programming tools. This unit arrives at your door fully programmed to your vehicle’s specific Vehicle Identification Number (VIN) and current mileage. This critical programming step ensures that the module communicates flawlessly with your vehicle’s existing systems, including the ignition key and security protocols. The result is a true plug-and-play installation. Simply disconnect the old module, connect this new one, and you’re ready to get back on the road. It’s the most efficient and cost-effective way to solve complex electronic issues.
From the Diagnostic Bay
We recently had a 2009 Jeep Patriot come in with a classic complaint: it would run fine for about 15 minutes and then stall without warning, refusing to restart until it cooled down. The owner had already replaced the crankshaft and camshaft sensors based on generic advice, with no success. Our technician connected a scope and found that the 5-volt reference signal supplied by the ECM to these sensors was dropping out as the module heated up. This is a common internal failure. We installed one of our pre-programmed modules, and the vehicle ran perfectly, demonstrating that the problem was in the computer all along, not the sensors it was controlling.
Is a Failing 2007-2010 Caliber Engine Computer Causing Your Problems?
A faulty ECM can manifest in a wide variety of symptoms that can be easily misdiagnosed. If you’re experiencing any of the following, a failing engine computer is a very likely culprit. This module is engineered to resolve these common failure points and restore proper function to your vehicle.
Common Symptoms of a Faulty ECM
- ✔ Persistent Check Engine Light (CEL) that won’t clear
- ✔ Vehicle refuses to start or has difficulty starting
- ✔ Rough or erratic engine idle
- ✔ Sudden stalling or engine hesitation while driving
- ✔ Noticeable decrease in fuel economy
- ✔ Poor engine performance and lack of power
- ✔ Communication errors with diagnostic scan tools
- ✔ Inconsistent or incorrect sensor readings
- ✔ Automatic transmission shifting problems
Guaranteed Fitment & Compatibility
This Engine Control Module is a direct replacement for a wide range of vehicles and part numbers, ensuring you get the correct component the first time. Please verify your vehicle and original part number against the list below.
This part fits the following vehicles:
- 2007-2010 Dodge Caliber
- 2007-2010 Jeep Patriot
- 2007-2010 Jeep Compass
This unit is a direct replacement for the following part numbers: 05150471AA, 05150523AA, 68043260AA, 68043260AB, 04692101AD, 04692101AE, 04692101AF, 68043260AC, 68043260AD, 68043261AC, 68043261AA, 68043261AB, 68070011AA, 68071022AA, 05033359AJ, 05187817AF, 68000107AF, 68026147AA, 68026147AC, 68028201AA, 68028201AC, 68028205AB, 68044228AA
Frequently Asked Questions
Is this engine computer really plug and play?
Yes, absolutely. We program the module with the VIN you provide during checkout. This ensures it is fully synchronized with your vehicle’s security system and other modules. No further programming or dealer visit is required.
Where do I provide my VIN and mileage?
You can provide your vehicle’s VIN and current mileage during the checkout process. There will be a specific field for this information. Accurate information is crucial for correct programming.
Do I need to send my old computer (core) back?
This purchase does not require a core return. You can keep or responsibly dispose of your old module without any core charge or obligation to send it back to us.
What tools are needed for installation?
Installation is typically straightforward and requires only basic hand tools, such as a socket set and ratchet. The most important step is to disconnect the vehicle’s battery before you begin to prevent any electrical damage.
How do I locate the ECM on my 2007-2010 Caliber, Patriot, or Compass?
On these models, the ECM is typically located in the engine bay, mounted to the firewall or inner fender. It is a metal box with several large electrical connectors. A quick search for your specific model and year will provide diagrams and videos for its exact location.
Will this fix my specific problem?
This module is designed to fix all issues directly caused by a faulty ECM. While we cannot diagnose your vehicle remotely, the symptoms listed on this page are the most common indicators of ECM failure. For a definitive diagnosis, we always recommend consulting a professional technician.