Restore Peak Performance to Your Vehicle
Is your Dodge Caliber, Jeep Patriot, or Jeep Compass suffering from frustrating and unpredictable issues? A faulty Engine Control Module (ECM) is often the culprit behind problems like a persistent check engine light, poor fuel economy, stalling, or a complete no-start condition. This direct-fit replacement engine computer, part number 04692101AF, is the definitive solution to restore your vehicle’s reliability and drivability. It arrives at your door fully programmed to your specific Vehicle Identification Number (VIN) and mileage, eliminating the need for expensive dealership programming. This is a true Plug & Play solution designed to get you back on the road with confidence.
From the Diagnostic Bay
We had a 2009 Dodge Caliber come into the shop that had its owner completely stumped. The car would randomly stall at traffic lights and occasionally refuse to start, but there were no consistent trouble codes—just a generic U-code for lost communication. The owner had already replaced the battery and checked the alternator. After running a full diagnostic sweep and verifying the integrity of the wiring harness, we pinpointed the issue: an internally failing ECM. The module was intermittently dropping communication with the rest of the car’s systems. Instead of a costly trip to the dealer for a new module and programming, we sourced this pre-programmed unit. The installation took less than 30 minutes, and the Caliber started right up and ran perfectly. The customer saved hundreds of dollars and a lot of headaches.
Common Symptoms of a Failing ECM
- ✔ Persistent Check Engine Light (CEL) that won’t clear
- ✔ Engine stalling, stumbling, or misfiring
- ✔ Difficulty starting the vehicle or a no-start condition
- ✔ Noticeable decrease in fuel efficiency
- ✔ Poor engine performance and lack of power
- ✔ Erratic automatic transmission shifting
- ✔ Communication errors with diagnostic scan tools
- ✔ ABS, traction control, or other warning lights illuminating
Installation for your 2007-2010 Caliber Engine Computer
Installing your replacement ECM is a straightforward process that can be done with basic hand tools. Because this unit comes pre-programmed, you will not need any special diagnostic equipment. The general steps are as follows:
- Safety First: Disconnect the negative terminal from your vehicle’s battery to prevent any electrical shorts.
- Locate the ECM: On most Caliber, Patriot, and Compass models, the ECM is located in the engine bay, typically mounted to the firewall or inner fender.
- Disconnect and Remove: Carefully unplug the electrical connectors from the old module. There are usually locking tabs that need to be released. Once disconnected, unbolt the module from its mounting bracket.
- Install the New Module: Mount your new, pre-programmed ECM in the same location and securely fasten the bolts. Reconnect the electrical connectors, ensuring they click into place.
- Reconnect Battery: Reattach the negative battery terminal. The vehicle may need to go through a brief ‘relearn’ process, which usually involves letting it idle for a few minutes.
With this simple installation, you’ll have your vehicle running smoothly again in no time, saving you the time and expense of a dealership visit. This is the ideal solution for the savvy DIY mechanic or professional technician.
Guaranteed Fitment and Compatibility
This module is a direct replacement for a wide range of vehicles, ensuring broad compatibility. It is designed to work seamlessly with the following makes and models:
- Dodge Caliber: 2007, 2008, 2009, 2010 (1.8L, 2.0L, 2.4L engines)
- Jeep Patriot: 2007, 2008, 2009, 2010
- Jeep Compass: 2007, 2008, 2009, 2010
This unit replaces the following part numbers: 05150471AA, 05150523AA, 68043260AA, 68043260AB, 04692101AD, 04692101AE, 04692101AF, 68043260AC, 68043260AD, 68043261AC, 68043261AA, 68043261AB, 68070011AA, 68071022AA, 05033359AJ, 05187817AF, 68000107AF, 68026147AA, 68026147AC, 68028201AA, 68028201AC, 68028205AB, 68044228AA. Ordering this part ensures you are receiving a fully compatible module for your vehicle.
Don’t let a faulty module keep your car off the road. By choosing our pre-programmed 2007-2010 Caliber Engine Computer, you are choosing a reliable, cost-effective, and simple solution. Order today and restore your vehicle’s proper function.
Frequently Asked Questions
What does “Plug & Play” really mean?
Plug & Play means the engine computer you receive has been pre-programmed with your vehicle’s specific VIN, mileage, and immobilizer information. You simply need to install it, and it will work immediately without requiring any additional programming from a dealership or mechanic.
What information do you need to program the module?
To ensure perfect compatibility, we require your vehicle’s 17-digit Vehicle Identification Number (VIN) and the current mileage at the time of purchase. Please provide this information during checkout.
Will this fix my check engine light?
If the check engine light is on due to a fault within the original engine computer, this replacement part will solve the problem. However, if the light is caused by another failing sensor or component on the vehicle, that issue will still need to be addressed separately.
Is this part also for a Jeep Patriot or Compass?
Yes. This engine control module is fully compatible with 2007-2010 Jeep Patriot and Jeep Compass models, in addition to the Dodge Caliber. It shares the same internal hardware and programming capabilities across these platforms.
Do I need to send my old computer back?
No core charge is required for this part. You do not need to return your old, non-functional engine computer to us.
How can I be sure I’m ordering the correct part number?
The best way to confirm is to check the part number on the label of your existing module. This part, 04692101AF, is a direct replacement for all the part numbers listed in the description. If your number is on that list, this part is a guaranteed match.