If you’re dealing with frustrating and unpredictable issues in your Dodge Caliber, Jeep Compass, or Jeep Patriot, a failing Engine Control Module (ECM) is often the culprit. Symptoms like a no-start condition, random stalling, poor fuel economy, or a persistent check engine light can make your vehicle unreliable. This isn’t just an inconvenience; it’s a problem that needs a solid, straightforward solution. We offer a dependable, pre-programmed 2007-2010 Caliber Engine Computer that eliminates the guesswork and gets you back on the road without the typical dealership hassle and expense.
The biggest challenge with replacing an ECM has always been the programming. In the past, you’d have to buy the part, install it, and then have your vehicle towed to a dealer for expensive flashing. Our process completely removes that step. We flash this module with your vehicle’s specific VIN and mileage before it even ships. When it arrives at your door, it’s a true plug-and-play part. You can install it in your own garage and get your vehicle running correctly again in under an hour.
From the Diagnostic Bay
I remember a 2009 Jeep Patriot that came into the shop with a list of baffling symptoms. The owner reported it would randomly refuse to start, and when it did run, the throttle response was erratic. The dashboard was lit up with a check engine light and the electronic throttle control warning. A quick scan pulled up code U0100 (Lost Communication with ECM/PCM) and P0606 (ECM/PCM Processor Fault). After verifying the wiring and power/ground circuits to the module were solid, it was clear the ECM itself was failing internally. Instead of a costly dealer part and programming fee, we installed one of these pre-programmed units. The entire job took less than 30 minutes, all codes cleared, and the Patriot ran like new. It’s a perfect example of how the right part can save hundreds in diagnostic time and repair costs.
Is Your Dodge or Jeep Showing These Signs?
A failing ECM can manifest in many ways. If you’re experiencing any of the following, this module is the likely solution:
- ✔ Vehicle will not start or is very difficult to start
- ✔ Check Engine Light is on with communication codes (e.g., U0100) or internal processor codes (P0601, P0606)
- ✔ Poor or erratic engine performance and shifting
- ✔ Drastic decrease in fuel economy
- ✔ Stalling for no apparent reason
- ✔ Other modules on the vehicle are not communicating with the engine computer
A Straightforward Guide to Installation
Installing your replacement 2007-2010 Caliber Engine Computer is a simple process that doesn’t require specialized tools. Just follow these steps for a successful repair:
- Safety First: Disconnect the negative terminal from your vehicle’s battery and secure it away from the post.
- Locate the ECM: On these models, the engine computer is typically located in the engine bay, often near the battery or firewall. It’s a metal box with several large electrical connectors.
- Disconnect and Remove: Carefully unplug the electrical harnesses from the old module. There are usually release tabs you’ll need to press. Once disconnected, unbolt the module from its mounting bracket.
- Install the New Module: Bolt the new, pre-programmed ECM into place. Securely reconnect the electrical harnesses, ensuring they click into place.
- Final Steps: Reconnect the negative battery terminal. The vehicle is now ready to start. The computer will perform a self-learning process over the first few drive cycles to fine-tune performance.
Verified Vehicle Compatibility
This engine control module is a direct-fit replacement for a wide range of vehicles, ensuring proper function and communication. It is compatible with the following part numbers: 05150471AA, 05150523AA, 68043260AA, 68043260AB, 04692101AD, 04692101AE, 04692101AF, 68043260AC, 68043260AD, 68043261AC, 68043261AA, 68043261AB, 68070011AA, 68071022AA, 05033359AJ, 05187817AF, 68000107AF, 68026147AA, 68026147AC, 68028201AA, 68028201AC, 68028205AB, and 68044228AA.
- Dodge Caliber: 2007-2008 (All Engines)
- Dodge Caliber: 2009 (1.8L, 2.0L Gasoline, 2.4L ED3)
- Dodge Caliber: 2010 (2.0L, 2.4L)
- Jeep Compass: 2007-2010
- Jeep Patriot: 2007-2010
By ordering this pre-programmed 2007-2010 Caliber Engine Computer, you are choosing the most efficient and reliable path to resolving your vehicle’s electronic issues. Restore your car’s performance and your peace of mind today.
Do I need to do any programming after I install this computer?
Do I need to do any programming after I install this computer?
No. This engine computer arrives at your door fully programmed to your vehicle’s VIN and mileage. It is a 100% plug-and-play solution, requiring no further action from a dealer or mechanic.
How do I provide my VIN and mileage?
You can provide your vehicle’s VIN and current mileage during the checkout process. Please double-check the information for accuracy to ensure a perfect match for your vehicle.
Will this fix my specific check engine light codes?
This ECM is a common solution for internal processor failure codes like P0601, P0606, and P060A, as well as communication codes like U0100. If your diagnosis has confirmed the ECM is the fault, this part will resolve those issues.
Is this compatible with my 2009 Caliber 2.4L?
Yes, this module is compatible with the 2009 Dodge Caliber with the 2.4L engine (option code ED3), as well as the 1.8L and 2.0L engines for that model year.
What if I order the wrong part?
Our VIN programming process serves as a final check. If the part you ordered is not compatible with the VIN you provide, our team will contact you before programming to ensure you get the correct module for your vehicle.