Is Your Dodge Caliber, Jeep Patriot, or Compass Acting Up?
If you’re dealing with frustrating issues like random stalling, a persistent check engine light that won’t go away, erratic shifting, or a complete no-start condition, the problem often points directly to a failing Engine Control Module (ECM). For many 2007-2010 Dodge and Jeep owners, these symptoms can turn a reliable vehicle into a source of constant stress. You’ve likely replaced sensors and checked wiring, only to have the problems return. This is where we come in.
A Technician’s Real-World Experience
“A customer’s 2009 Caliber came into my shop last month with a check engine light and what they described as ‘jerky’ transmission behavior. The codes pointed to a loss of communication with the TCM (Transmission Control Module). After spending hours checking the wiring harness and even swapping in a known-good TIPM, the issue persisted. On a hunch, we focused on the ECM. It turns out the engine computer’s internal processor was failing, causing it to drop communication packets to the other modules on the CAN bus network. A new, properly programmed ECM solved everything instantly. It’s a classic case I’ve seen dozens of times on these platforms where the ECM is the hidden culprit behind what looks like a transmission or power module failure.”
The Simple, Permanent Solution: A Plug-and-Play ECM
Forget expensive dealership visits and the hassle of finding a shop that can program a new module. This replacement 2007-2010 Caliber Engine Computer arrives at your door fully programmed to your vehicle’s specific VIN and mileage. This isn’t just a part; it’s a complete, ready-to-install solution designed to get you back on the road with confidence.
Why Choose Our Programmed 2007-2010 Caliber Engine Computer?
- โ No Additional Programming Required: We handle all the flashing and software configuration before it ships. It’s truly plug-and-play.
- โ Guaranteed VIN Matching: By programming the module to your VIN, we ensure it communicates perfectly with your vehicle’s other systems, like the anti-theft immobilizer and transmission controller.
- โ Eliminate Common Faults: This is a direct fix for common issues like false sensor codes (U-codes, P0600-P0606 series), poor fuel economy, and intermittent stalling.
- โ Restored Drivability: Get back the smooth acceleration, crisp shifting, and reliable starting you expect from your vehicle.
Plug-and-Play Installation: No Dealer Visit Required
You can perform this installation yourself in your driveway with basic hand tools. Follow these simple steps:
- Safety First: Always disconnect the negative terminal from your vehicle’s battery and wait 10 minutes for the system capacitors to discharge.
- Locate the ECM: On the Dodge Caliber, Jeep Patriot, and Compass, the ECM is typically located in the engine bay, mounted to the side of the battery tray or near the firewall.
- Disconnect Connectors: Carefully unclip the wiring harness connectors from the old module. Inspect the pins for any corrosion or damage and clean them with electrical contact cleaner if necessary.
- Remove the Old Module: Unbolt the old ECM from its mounting bracket. It’s usually held in by three or four 10mm or 13mm bolts.
- Install the New Module: Bolt your new, pre-programmed ECM into place.
- Reconnect Everything: Securely plug the wiring harnesses back into the new module until they click. Reconnect your negative battery terminal.
- Final Key Cycle: Turn the key to the ‘ON’ position (without starting the engine) for 15 seconds, then turn it off. Repeat this 3 times. This allows the new ECM to sync with the vehicle’s other modules. Start the engine and let it idle for a few minutes. Your vehicle is ready to drive!
Guaranteed Compatibility
This module is a direct replacement for a wide range of part numbers, ensuring a perfect fit and function for your vehicle. It is compatible with the following models and part numbers:
Fits These Vehicles:
- 2007-2008 Dodge CALIBER (All Engines)
- 2009 Dodge CALIBER (1.8L, 2.0L Gasoline, 2.4L w/ engine opt ED3)
- 2010 Dodge CALIBER (2.0L, 2.4L)
- 2007-2010 Jeep PATRIOT
- 2007-2010 Jeep COMPASS
Replaces Part Numbers: 05150471AA, 05150523AA, 68043260AA, 68043260AB, 04692101AD, 04692101AE, 04692101AF, 68043260AC, 68043260AD, 68043261AC, 68043261AA, 68043261AB, 68070011AA, 68071022AA, 05033359AJ, 05187817AF, 68000107AF, 68026147AA, 68026147AC, 68028201AA, 68028201AC, 68028205AB, 68044228AA and more.