2006-2007 Monte Carlo BCM 25892622 | Programmed to Your VIN

Restore Your Monte Carlo’s Electrical System!

Stop chasing electrical gremlins. This Body Control Module (BCM) for your 2006-2007 Monte Carlo fixes issues like flickering lights and faulty power accessories. It comes pre-programmed to your car’s VIN for a simple installation process. Fix your issue today!

$224.95

+11.99 USPS Priority Shipping

Availability: In stock



SKU: 591-01465-1096 Categories: ,
Guaranteed Safe Checkout

Is Your Monte Carlo Acting Possessed?

If you’re dealing with a frustrating mix of electrical gremlins in your 2006 or 2007 Monte Carlo, you’re not alone. I’ve seen it countless times in my shop: the instrument cluster lights flicker randomly, the power windows or locks work intermittently, the radio cuts out, or you get a persistent “Service Security System” message. These aren’t separate problems; they’re classic symptoms of a failing Body Control Module (BCM). The BCM is the central hub for your car’s body electronics, and when it starts to go, it creates chaos.

Real-World Diagnosis: “A customer’s 2007 Monte Carlo SS came in last week with these exact symptoms. The radio would shut off, and the security light would flash, sometimes preventing the car from starting. After confirming power and grounds were good, a scan tool showed a ‘Loss of Communication’ with the BCM. It’s a textbook failure on this W-body platform, often due to internal circuit board corrosion or solder joint failure over time. Replacing the BCM was the definitive fix.”

The Direct-Fit, No-Hassle Solution

Forget expensive diagnostic fees and programming charges at the dealership. This Body Control Module is the straightforward solution to restore your car’s functionality. We take all the guesswork out of the process. Simply provide us with your vehicle’s VIN during checkout, and our technicians will program the module with the latest GM software specific to your Monte Carlo’s options. It arrives at your door ready for installation.

Common Symptoms of a Failing BCM:

  • โœ” Intermittent or non-functional power windows, door locks, or mirrors.
  • โœ” Flickering or dead instrument cluster lights and gauges.
  • โœ” Radio or climate control system turning on and off by itself.
  • โœ” “Service Security System” or “Service Theft System” messages.
  • โœ” Erratic interior or exterior lighting behavior.
  • โœ” No-start condition due to the anti-theft system not recognizing the key.

Easy Installation Guide for your 2006-2007 Monte Carlo BCM

Replacing the BCM on your Monte Carlo is a manageable job for a confident DIYer. The module is located on the left-hand side of the steering column, typically attached to a metal bracket.

  1. Safety First: Disconnect the negative terminal from your car’s battery and wait 10-15 minutes to allow all modules to power down completely.
  2. Access the Module: Remove the lower dash panel (knee bolster) below the steering wheel. It’s usually held in by a few screws and clips.
  3. Locate the BCM: Identify the Body Control Module. It’s a black plastic box with several large multi-pin electrical connectors.
  4. Disconnect and Remove: Carefully unplug all electrical connectors. They have locking tabs that need to be depressed. Once disconnected, unbolt the module from its mounting bracket.
  5. Install the New BCM: Mount your new, pre-programmed BCM in the reverse order of removal. Ensure all electrical connectors are plugged in firmly until they click into place.
  6. Reconnect and Test: Reconnect the negative battery terminal. Turn the key to the ‘ON’ position (without starting) and verify that your interior lights, radio, and power accessories are functioning correctly.

Critical Post-Installation Steps (Required)

After installing your new BCM, two final procedures are necessary to ensure full functionality and safety. These steps require a professional-grade bidirectional scan tool.

  • Airbag System Reset: The BCM and the airbag module (SDM) communicate. You must perform the ‘Setup SDM Primary Key in BCM’ procedure. This re-establishes the security handshake between the modules and will turn off the airbag warning light on your dash.
  • Brake Pedal Position Sensor Relearn: Some vehicles require a recalibration of the brake pedal position sensor after a BCM replacement. This ensures the brake lights and stability control systems function correctly.

Guaranteed Fitment & Part Number Compatibility

This module is a direct replacement for your 2006-2007 Monte Carlo and is also compatible with a wide range of other GM vehicles. It replaces the following part numbers:

10382479, 15093910, 15276271, 15299986, 15819552, 15828601, 15837419, 15872388, 15872421, 15880684, 15921352, 15921353, 15948438, 15948439, 20815898, 20839063, 20864767, 20864768, 20921435, 20921436, 20935349, 22860591, 25826124, 25826125, 25847588, 25847589, 25892622, 25910474, 25934762, 25934763, 95151084

Genuine OEM

Yes

Condition

Refurbished

MPN

25892622

Interchange part number

PartNumber

591

Model

Monte Carlo

Year

2013

Brand

GM

Manufacturer Part Number

, , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

Scroll to Top