2006-2007 Monte Carlo BCM 15093910 Body Control Module | Cloning Service

End Electrical Gremlins Fast.

Stop the frustrating electrical issues in your Monte Carlo. This Body Control Module (BCM) is prepared for your vehicle via our professional cloning service, transferring your car’s data to make it a true plug-and-play replacement. No expensive dealership programming is required. Restore your car’s power windows, lights, and security system to perfect working order. Order today and get your Monte Carlo running right!

$224.95

+11.99 USPS Priority Shipping

Availability: In stock



SKU: 591-01465-357 Categories: ,
Guaranteed Safe Checkout

Restore Your Monte Carlo’s Electrical System with a Plug-and-Play Solution

Are you dealing with baffling electrical issues in your 2006-2007 Chevrolet Monte Carlo? Flickering dash lights, malfunctioning power windows, a security system that acts up, or even a no-start condition can often be traced back to a single culprit: a failing Body Control Module (BCM). As the central command center for your vehicle’s body electronics, when the BCM falters, it can create a cascade of frustrating and unpredictable problems. Instead of facing a costly trip to the dealership for diagnostics and programming, our professional cloning service offers a direct, reliable, and affordable solution.

This service is designed to get you back on the road with minimal hassle. We transfer the critical data from your original BCM directly onto this replacement unit. This means the replacement module arrives at your door pre-programmed and ready for installation, perfectly matched to your car’s specific configuration using your VIN. By cloning your existing module, you bypass the need for expensive factory scan tools and complex key relearn procedures, making this the ideal fix for both seasoned mechanics and DIY enthusiasts.

A Technician’s Notebook

I remember a 2007 Monte Carlo SS that came into the shop with a classic ‘haunted car’ complaint. The dome lights would randomly turn on while driving, the radio would shut off, and the anti-theft light would flash, preventing it from starting about once a week. The owner had already replaced the battery and checked the grounds. After hooking up the scanner, I saw a handful of U-codes (U0140, U0155) indicating a loss of communication with the BCM. A visual inspection revealed no damage, but a wiggle test of the main connector caused the symptoms to appear instantly. The internal circuits of the original BCM were failing. We performed our cloning service, and the replacement 2006-2007 Monte Carlo BCM had the car’s electrical systems functioning perfectly within an hour of installation. It’s a textbook example of how a direct replacement service saves hours of diagnostic headaches.

Signs Your Monte Carlo’s BCM is Failing

A faulty Body Control Module can manifest in numerous ways. If you’re experiencing any of the following, your BCM may be the root cause:

  • ✔ Power windows, door locks, or mirrors operating erratically or not at all.
  • ✔ Interior or exterior lights (headlights, taillights, dome lights) staying on or not turning on.
  • ✔ The security system preventing the car from starting or the alarm sounding randomly.
  • ✔ The instrument cluster displaying incorrect information or warning lights (like the airbag light) illuminating without cause.
  • ✔ Communication error codes, typically in the U-series (e.g., U0140), stored in the vehicle’s computer system.
  • ✔ Wipers behaving erratically or not parking in the correct position.

Your Straightforward BCM Installation Guide

Installing your cloned 2006-2007 Monte Carlo BCM is a manageable task. For this specific model, the BCM is located behind the driver’s side of the dashboard, near the steering column. Always consult a factory service manual for detailed diagrams.

  1. Safety First: Disconnect the negative terminal from your vehicle’s battery to prevent any electrical shorts.
  2. Access the Module: You will likely need to remove the lower dash panel beneath the steering wheel to gain access to the BCM.
  3. Disconnect and Remove: Carefully unplug the electrical connectors from the old BCM. They have locking tabs that must be depressed. Once disconnected, unbolt or unclip the module from its mounting bracket.
  4. Install the New Module: Mount the replacement BCM in the same location and securely reconnect all electrical connectors. Ensure they click into place.
  5. Final Steps: Reinstall the dash panel and reconnect the negative battery terminal. Start the vehicle to confirm that all electronic functions are restored. Note the post-installation procedures below, as some systems may require recalibration.

Important Post-Installation Information

While our cloning service handles the primary programming, some vehicle systems may require a ‘handshake’ with the new BCM. Please be aware of the following potential procedures:

  • Airbag System Sync: If the airbag warning light is on after installation, a professional scan tool is needed to perform the ‘Setup SDM Primary Key in BCM’ procedure. This syncs the airbag system with the new BCM.
  • Brake Pedal Position Relearn: On some models, a brake pedal position sensor recalibration might be necessary to ensure correct brake light operation and traction control functionality.

Disclaimer: Specific procedures can vary. Always refer to a factory service manual or a qualified technician for guidance.

Verified Vehicle Compatibility List

This BCM is a direct-fit replacement for a wide range of GM vehicles and is interchangeable with multiple part numbers. Please verify your part number or contact us with your VIN to confirm compatibility.

Replaces Part Numbers: 10382479, 15093910, 15276271, 15299986, 15819552, 15828601, 15837419, 15872388, 15872421, 15880684, 15921352, 15921353, 15948438, 15948439, 20815898, 20839063, 20864767, 20864768, 20921435, 20921436, 20935349, 22860591, 25826124, 25826125, 25847588, 25847589, 25892622, 25910474, 25934762, 25934763, 95151084

Fits Models Including:

ACADIA 07-12
AVALANCHE 1500 10
CAPRICE 11-13
CAPTIVA SPORT 12
CTS 08-13
DTS 06-11
ENCLAVE 08-12
EQUINOX 07-09
ESCALADE 10
ESCALADE ESV 10
ESCALADE EXT 10
EXPRESS VANS 08-12
G8 08-09
HUMMER H2 08-09
IMPALA 06-13
LUCERNE 06-11
MONTE CARLO 06-07
OUTLOOK 07-10
SAVANA VANS 08-12
SRX 07-09
STS 10
SUBURBAN 1500 10
TAHOE 10
TORRENT 07-09
TRAVERSE 09-12
VUE 08-10
YUKON 10
YUKON XL 1500 10

Frequently Asked Questions

How does the cloning service work?

After you place your order, you’ll ship your original BCM to us. We use specialized equipment to extract the unique vehicle data and transfer it to the replacement module. This makes the new module a perfect electronic match for your car, eliminating the need for dealership programming. We then ship both your original module and the ready-to-install replacement back to you.

Why do you need my VIN?

We require your Vehicle Identification Number (VIN) to load the latest GM software and firmware updates onto the module before the cloning process. This ensures your replacement 2006-2007 Monte Carlo BCM has the most current operational data for optimal performance and reliability.

Do you keep my old BCM?

No, we do not keep your original module. Our core return policy is simple: your original BCM is always returned to you along with the newly programmed replacement unit. You get to keep your original part.

Is this a difficult part to install myself?

For someone with basic mechanical skills and tools, this is a very manageable job. The main challenge is accessing the module, which is typically under the dash. Since our cloning service removes the need for programming, the physical swap is the only step required. Please see our installation guide above for a general overview.

Genuine OEM

Yes

Condition

Refurbished

MPN

15093910

Interchange part number

PartNumber

591

Model

Monte Carlo

Year

2013

Brand

GM

Manufacturer Part Number

Scroll to Top