2005-2006 Grand Cherokee ECM 05094898ZB Programmed Engine Computer

End Your Jeep’s Engine Problems

Get your 2005-2006 Jeep Grand Cherokee running right again with this plug-and-play Engine Control Module. It arrives pre-programmed to your VIN and mileage, eliminating the need for costly dealer visits. This is the direct-fit solution for fixing stalling, no-start conditions, and persistent check engine lights caused by a faulty computer. Restore your Jeep’s performance and reliability today. Order now for a hassle-free fix!

$149.95

+11.99 USPS Priority Shipping

Out of stock

SKU: 590-07674-19 Categories: ,
Guaranteed Safe Checkout

Restore Your Jeep’s Performance and Reliability

If you’re dealing with frustrating and unpredictable engine problems in your 2005-2006 Jeep Grand Cherokee, a failing Engine Control Module (ECM) is often the culprit. As a technician with over two decades of experience, I’ve seen firsthand how a faulty ECM can cause a cascade of issues—from a persistent check engine light and stalling to a complete no-start condition. This isn’t just an inconvenience; it’s a matter of reliability. You need a solution that works right out of the box, and this pre-programmed engine computer is designed to be exactly that.

This module arrives fully programmed to your vehicle’s specific VIN and mileage, eliminating the need for expensive dealership visits or specialized programming tools. It’s a true plug-and-play fix that restores the critical communication between your engine’s sensors and systems. By replacing your old, malfunctioning unit, you’re not just clearing codes; you’re restoring the precise fuel delivery, ignition timing, and transmission logic your Grand Cherokee needs to run smoothly and efficiently. This is the definitive solution for getting your 3.7L 4×4 back on the road with confidence.

From the Diagnostic Bay: The Intermittent No-Start Nightmare

I remember a 2006 Grand Cherokee that came into my shop with an issue that was driving the owner crazy. It would start perfectly for a week, then suddenly refuse to crank. There were no consistent codes, just a frustrating U0100 (Lost Communication with ECM/PCM) that would pop up sporadically. The owner had already replaced the battery and checked the starter. We spent hours tracing wiring harnesses, looking for a phantom short. Finally, we decided to monitor the ECM’s internal voltage on a scope during startup. We discovered the processor was intermittently failing to initialize. We installed a pre-programmed 2005-2006 Grand Cherokee ECM, and the problem vanished instantly. It was a powerful reminder that sometimes the ‘brain’ itself is the source of the ghost in the machine.

Common Signs of a Failing ECM

  • ✔ Engine stalling, sputtering, or misfiring
  • ✔ Complete no-start or intermittent starting issues
  • ✔ Check Engine Light is on with codes like P0601 (Internal Control Module Memory Check Sum Error) or P0606 (ECM/PCM Processor Fault)
  • ✔ Poor fuel economy or a noticeable loss of power
  • ✔ Erratic automatic transmission shifting
  • ✔ Communication errors with diagnostic scan tools

A Straightforward Guide to Installation

  1. ✔ Safety First: Disconnect the negative terminal from your vehicle’s battery and wait 10-15 minutes for the system capacitors to discharge.
  2. ✔ Locate the Module: On your Grand Cherokee, the ECM is found in the engine compartment, typically mounted on the right-hand (passenger) side firewall.
  3. ✔ Disconnect Connectors: Carefully unclip the wiring harness connectors from the old ECM. There are usually locking tabs that need to be depressed or slid. Do not force them.
  4. ✔ Remove the Old ECM: Unbolt the mounting hardware that secures the old module to the vehicle. Keep the hardware, as you will need it for the new module.
  5. ✔ Install the New ECM: Mount your new, pre-programmed module in the same location using the original hardware.
  6. ✔ Reconnect Everything: Firmly plug the wiring harness connectors into the new ECM until they click into place. Reconnect the negative battery terminal.
  7. ✔ Final Check: Turn the key to the ‘On’ position (without starting the engine) for 10 seconds to allow the systems to initialize, then start your vehicle. The installation is complete!

Verified Vehicle Compatibility

This Engine Control Module is a direct-fit replacement for the following vehicles, ensuring a perfect match and seamless operation. Please verify your vehicle’s specifications before ordering.

  • Make: Jeep
  • Model: Grand Cherokee
  • Years: 2005-2006
  • Engine: 3.7L V6
  • Drivetrain: 4×4

This unit is also a direct replacement for the following part numbers, guaranteeing compatibility if your original module has any of these identifiers: 05094895AB, 05094898AA, 05094898AB, 05094898AC, 05094898AD, 05094898AE, 05094898ZB, 56044742AC, 56044742AD, 05094898AF.

Do I need to get this ECM programmed by a dealer?
No. This module comes fully programmed to your vehicle’s VIN and mileage. It is a plug-and-play solution that requires no additional programming.
Where is the ECM located on my 2005 Grand Cherokee?
The Engine Control Module (ECM) is located in the engine bay, on the right-hand (passenger side) rear firewall.
Will this fix my check engine light?
If the check engine light is caused by an internal failure of the ECM (such as code P0601), then this part will resolve the issue. You should always perform a proper diagnosis to confirm the ECM is the point of failure before ordering.
How do I provide my VIN and mileage?
You will be prompted to enter your vehicle’s VIN and current mileage during the checkout process. This information is required for us to program the module correctly before shipping.
Is this compatible with a 2-wheel drive model?
This specific part is designated for 4×4 models. Please verify the part number and options for your vehicle to ensure correct fitment.
Year
Genuine OEM

Yes

Interchange part number

Condition

Seller refurbished

Model

grand-cherokee

Make

Year

2006

GTIN

Does not apply

Brand

JEEP

Manufacturer Part Number

, , , , , , , , , ,

MPN

05094898zb

Scroll to Top