Restore Your Camaro’s Electrical System with a Plug-and-Play Solution
Is your 2014-2015 Chevrolet Camaro suffering from bizarre electrical issues? Flickering lights, malfunctioning power windows, or a security system that has a mind of its own are classic signs of a failing Body Control Module (BCM). The BCM is the central command center for your car’s body electronics, and when it falters, it can cause a cascade of frustrating problems. Dealerships often charge a fortune for a new module plus mandatory programming fees. We offer a smarter, more affordable solution.
This listing is for a fully tested replacement BCM that comes pre-programmed with your vehicle’s exact data. Our professional cloning service transfers all the critical information—including the VIN and security settings—from your original module to this replacement unit. The result is a true plug-and-play component that restores function without any need for dealer intervention. Simply send us your original BCM, and we’ll handle the complex technical work, shipping you back a module that’s ready for installation right out of the box.
A Technician’s Notebook: The Camaro with a Ghost
I remember a 2014 Camaro convertible that came into the shop with a list of symptoms that sounded like a haunting. The interior lights would fade in and out while driving, the radio would randomly shut off, and the driver’s side window wouldn’t drop properly when the door was opened. The owner had already replaced the battery, but the gremlins persisted. After hooking up the scan tool, I found a slew of U-codes (communication errors) pointing to a network problem originating at the BCM. Instead of a costly new module and a full vehicle reprogram, we used this exact cloning service. We had the customer’s original BCM cloned, and the replacement part solved every single issue. It’s a testament to how a targeted, precise repair can save hundreds of dollars and countless headaches.
Is Your Camaro’s BCM Failing? Watch for These Signs
A faulty BCM can manifest in numerous ways. As the nerve center for body electronics, its failure can disrupt systems you use every day. Here are some of the most common indicators I’ve seen in my 20+ years of diagnostics:
- ✔ Erratic power windows, door locks, or mirrors that work intermittently or not at all.
- ✔ Interior dome lights, dashboard lights, or exterior lights staying on or not turning on.
- ✔ The anti-theft or security system light flashing, preventing the car from starting.
- ✔ Instrument cluster warnings like “Service StabiliTrak” or other erroneous messages.
- ✔ Communication failure codes (U-codes) when scanned with a diagnostic tool.
- ✔ Remote keyless entry (fob) not working consistently.
A Straightforward Guide to Installation
Our goal is to make this process as simple as possible. After you place your order, we will contact you with shipping instructions for your original module. Once you receive the programmed replacement, installation is straightforward.
- Step 1: Safety First: Always disconnect the negative terminal from your vehicle’s battery before working on any electronic components.
- Step 2: Locate and Remove: On the 2014-2015 Camaro, the BCM is typically located behind the right-hand (passenger side) of the dashboard. Carefully remove any trim panels needed to access and unplug the module.
- Step 3: Install the Replacement: Secure the pre-programmed BCM we sent you into the mounting bracket and reconnect all the electrical connectors. Ensure they click firmly into place.
- Step 4: Power Up: Reconnect the negative battery terminal.
- Step 5: Final Checks: Start the vehicle and test all body functions—windows, locks, lights, and radio—to confirm proper operation. Note the post-installation procedures below, as some minor recalibrations may be necessary.
Important Post-Installation Information
In some cases, your vehicle may require minor system recalibrations after the new BCM is installed. These are standard procedures and do not indicate a problem with the module.
- Airbag System Sync: If the airbag warning light is illuminated after installation, a professional scan tool is needed to perform the ‘Setup SDM Primary Key in BCM’ function. This syncs the airbag system with the new BCM.
- Brake Pedal Position Relearn: To ensure proper brake light and traction control operation, a brake pedal position sensor relearn may be required. This is a simple procedure for any qualified technician with a bi-directional scan tool.
Disclaimer: Specific procedures can vary by vehicle. Always consult a factory service manual or a qualified technician for guidance.
Verified Vehicle Compatibility
This BCM programming service is compatible with a wide range of GM vehicles. Please verify your part number is on this list. This module is a direct replacement for part numbers: 13580698, 13578458, 13589115, 13589637, 13590173, 13590851, 13591300, 13592376, 13593775, 13593776, and 13594564.
- Buick LaCrosse: 2014-2016
- Buick Regal: 2014-2017
- Cadillac ELR: 2014-2016
- Cadillac SRX: 2014-2016
- Chevrolet Camaro: 2014-2015
- Chevrolet Malibu: 2014-2016 (including ‘Limited’ models)
- Chevrolet Spark EV: 2014-2016 (electric model)
- Chevrolet Volt: 2014-2015
Frequently Asked Questions
How does this cloning service work?
You purchase this service and ship your original BCM to us. We extract the unique software and security data and flash it onto a fully tested replacement module. We then ship the ready-to-install module back to you, eliminating any need for additional programming.
Is this better than buying a used BCM from a junkyard?
Absolutely. A used BCM is locked to the donor car’s VIN and security system. It will not work in your vehicle without expensive programming, which many shops cannot perform. Our service guarantees compatibility by using your car’s own data.
Where is the BCM located on my 2015 Camaro?
In the 2014-2015 Camaro, the Body Control Module is typically found behind the dashboard on the passenger’s side of the vehicle.
Do I have to send my old part back for a core charge?
No, there is no core charge. We only need your original module to perform the data transfer service. You can keep your original, non-working module afterward.
What if the airbag light comes on after I install it?
This is a known possibility. It simply means the airbag module (SDM) needs to be electronically ‘introduced’ to the new BCM. A repair shop with a professional-grade scan tool can perform the ‘Setup SDM Primary Key’ procedure in a few minutes to resolve this.