Restore Your Jeep’s Performance and Reliability
Is your 2009-2010 Jeep Commander or Grand Cherokee suffering from frustrating and unpredictable engine problems? Issues like a persistent check engine light, rough idling, stalling, or a complete no-start condition often point to a failing Engine Control Module (ECM). The ECM is the central computer of your vehicle, responsible for managing everything from fuel injection and ignition timing to emissions controls and transmission shifting. When it falters, the entire vehicle’s performance suffers. This replacement engine computer, part number 68060531AC, is the definitive solution to get your 3.7L V6 running like new again.
From the Diagnostic Bay
We had a 2010 Grand Cherokee 3.7L come into the shop that was a real head-scratcher. The owner had already replaced the crank sensor, cam sensor, and a full set of spark plugs chasing an intermittent stalling issue and a P0601 (Internal Control Module Memory Check Sum Error) code that would come and go. The vehicle would run fine for days, then suddenly die at a stoplight. After verifying the wiring harness and power/ground supplies to the computer were solid, we knew the culprit was internal to the ECM itself. These modules can develop micro-fractures on the circuit board from years of heat cycles and vibration. We installed one of our pre-programmed units, and the Jeep has been running perfectly ever since. It’s a classic case where chasing sensors can cost more time and money than addressing the root cause: the failing computer.
Is Your Jeep’s ECM Failing?
A faulty engine computer can manifest in numerous ways, often mimicking other component failures. If you’re experiencing any of the following, it’s a strong indicator that your ECM needs attention:
- âś” Check Engine Light: The light is on with codes related to internal processor errors (P0600-P0606) or random sensor circuit faults.
- âś” No-Start Condition: The engine cranks but refuses to start, despite having fuel and spark.
- âś” Engine Stalling: The engine dies unexpectedly while driving or idling.
- âś” Poor Performance: Noticeable loss of power, hesitation during acceleration, and decreased fuel economy.
- âś” Rough Idle: The engine runs erratically or shakes when the vehicle is stopped.
- âś” Erratic Shifting: The automatic transmission may shift harshly, late, or not at all, as the ECM communicates directly with the transmission controller.
The Plug & Play Solution: A Programmed 2009-2010 Commander ECM
The biggest hurdle in replacing a modern vehicle’s computer is the complex programming required to sync it with your specific vehicle. This is where our solution stands apart. We eliminate the need for an expensive trip to the dealership or a specialized mechanic. Before we ship your 2009-2010 Commander ECM, our technicians will professionally program it with your vehicle’s unique Vehicle Identification Number (VIN) and current mileage. This critical step ensures that the computer is a perfect match for your Jeep’s factory settings, security system (SKIM), and optional features. When it arrives, the installation is straightforward: disconnect the battery, swap the modules, reconnect the battery, and you’re ready to drive. No extra steps, no special tools, no hassle.
Guaranteed Fitment and Compatibility
This ECM is a direct replacement for 2009-2010 Jeep Commander and 2009-2010 Jeep Grand Cherokee models equipped with the 3.7L V6 engine. It is compatible with a wide range of original part numbers, ensuring you get the correct component for your vehicle. Please verify your part number against the list below:
Compatible Part Numbers: 05150467AA, 05150467AB, 68028166AB, 68028166AC, 68028166AD, 68028166AE, 68028166AF, 68060531AB, 68060531AC, 68060531AD, 68059198AA, 68059198AB, 68028167AB, 68028167AC, 68028167AD, 68028167AE, 68028162, 68059197, 68028163, 68028154, 68059196, 68028155, 68028155AD, 68028150, 68059195, 68028151, 68028174, 68028175, 68028176
Frequently Asked Questions
What information do you need to program this ECM?
We require your vehicle’s 17-digit Vehicle Identification Number (VIN) and the current mileage. You can provide this information during the checkout process. This ensures the 2009-2010 Commander ECM is perfectly matched to your Jeep’s security and systems.
Is this really a ‘Plug and Play’ installation?
Yes, absolutely. Because we handle all the necessary programming beforehand, you will not need to take your vehicle to a dealer or mechanic for additional flashing. Simply install the module, and your vehicle will start and run correctly.
Where is the ECM located on my 2009-2010 Commander or Grand Cherokee?
On these models, the Electronic Control Module is typically located in the engine compartment on the right-hand (passenger) side, often near the firewall or inner fender.
Will this fix my specific check engine light codes?
This module is the direct solution for internal processor failure codes (like P0601, P0606) and can resolve a host of other communication or sensor circuit codes that stem from a faulty computer. However, it’s always best to properly diagnose your vehicle to ensure the ECM is the root cause before ordering.
Do I need to send my old ECM back?
This listing does not require a core return. You can keep your old part, which saves you the time and expense of shipping it back to us.