Is Your Dodge Avenger or Sebring Running Rough?
If your 2008 Dodge Avenger or 2007-2008 Chrysler Sebring is experiencing frustrating issues like stalling, no-start conditions, a persistent check engine light, or erratic engine behavior, a failing Engine Control Module (ECM) is a very likely culprit. The ECM is the central computer of your vehicle, responsible for managing everything from fuel injection and ignition timing to transmission shifting and emissions control. When it fails, it can cause a cascade of problems that are often misdiagnosed, leading to costly and unnecessary repairs.
From the Diagnostic Bay
We recently had a 2008 Avenger 3.5L come into the shop with a complaint of intermittent stalling and a check engine light for a random misfire. The owner had already replaced the spark plugs, ignition coils, and even a camshaft position sensor at another shop with no success. After hooking up our advanced scanner, we noticed the live data for the fuel injectors was behaving erratically. Instead of immediately blaming the injectors, we checked the power and ground signals at the ECM connector. We found a weak ground, but the root cause was internal corrosion within the module itself, causing intermittent failures. A replacement, properly programmed 2008 Dodge Avenger ECM had the vehicle running perfectly in under an hour, saving the customer from further guesswork and expensive part replacements.
Common Symptoms of a Failing ECM
- âś” Check Engine Light is on with codes like P0601, P0605, or P0606.
- âś” Engine cranks but refuses to start.
- âś” Unexplained stalling or hesitation while driving.
- âś” Noticeable decrease in fuel economy.
- âś” Rough or unstable idle.
- âś” Automatic transmission shifting erratically or harshly.
- âś” Loss of power and poor acceleration.
- âś” Communication issues with diagnostic scan tools.
The Plug-and-Play Solution: Your Programmed 2008 Dodge Avenger ECM
This isn’t just a replacement part; it’s a complete, ready-to-install solution. We take the guesswork and hassle out of the repair process. Before shipping, this Engine Control Module is professionally programmed with your vehicle’s specific Vehicle Identification Number (VIN) and current mileage. This critical step ensures that the computer communicates flawlessly with all other modules in your car, including the anti-theft system (SKIM). The result is a true plug-and-play installation. Simply disconnect the old module, connect this new one, and turn the key. No expensive trips to the dealership for programming are required.
Guaranteed Fitment and Compatibility
This ECM is a direct-fit replacement for your 2008 Dodge Avenger or 2007-2008 Chrysler Sebring equipped with either the 2.7L or 3.5L V6 engine. It is compatible with a wide range of original part numbers, ensuring you get the correct component for your vehicle. Please verify your original part number against the list below to confirm compatibility.
This module replaces the following part numbers: 05033708AD, 05033708AE, 05033707AJ, 05033708AF, 05094721AA, 05094721AB, 05094721AC, 05094721AE, 05094721AG, 05094721AH, 05094721AI, 05094721AJ, 05094721AK, 05094721AL, 05094721AM, 05094721AN, 05150157AH, 05094721AO, 05094858AA, 05094858AC, 05094858AD, 05094858AE, 05094858AF, 05187343AF, 05150245AC
Frequently Asked Questions
Do I need to have this ECM programmed by a dealer?
No. This unit comes pre-programmed to your vehicle’s specific VIN and mileage. It is a plug-and-play module, ready for installation right out of the box. No further programming is needed.
What information do you need from me to program it?
During the checkout process, we will require your vehicle’s 17-digit VIN. This ensures we can load the correct software and security information for your specific car.
Where is the ECM located on my 2008 Dodge Avenger?
On the 2008 Dodge Avenger, the Engine Control Module is typically located in the engine bay, mounted to the driver’s side inner fender well, near the battery and fuse box.
Will this fix my check engine light?
If the check engine light is caused by an internal failure of the original ECM (common codes include P0601, P0605, P0606), then this replacement module will solve the problem. It is crucial to ensure that the root cause of the failure (e.g., a shorted sensor or wire) has been addressed before installing the new unit.
Is this a new or used part?
This is a high-quality, tested, and verified replacement part that meets or exceeds original equipment specifications. Each unit undergoes rigorous inspection and programming to ensure reliability and performance.