Is Your 2008 Dodge Avenger Experiencing Frustrating Engine Problems?
If your 2008 Dodge Avenger or 2007-2008 Chrysler Sebring is stalling, running rough, misfiring, or simply won’t start, a failing Engine Control Module (ECM) is a very likely culprit. The ECM is the central computer of your vehicle, responsible for managing everything from fuel injection and spark timing to transmission shifting and emissions control. When it begins to fail, it can cause a wide array of confusing and intermittent issues that can be difficult to diagnose. Don’t let a faulty computer keep your car off the road. This direct-fit replacement engine computer is the reliable solution you need.
The Simple, Plug-and-Play Solution
Forget about expensive dealership visits and the need for specialized programming tools. We take the hassle out of the repair process. This module arrives at your door fully programmed to your vehicle’s specific Vehicle Identification Number (VIN) and mileage. This means the installation is a straightforward, plug-and-play procedure. Simply disconnect the battery, swap the old module with this new one, reconnect the battery, and you’re ready to go. No additional flashing or programming is required, getting you back on the road quickly and affordably.
From the Diagnostic Bay
We had a 2008 Avenger come into the shop with a really strange issue. The owner complained of random stalling at traffic lights, but only when the A/C was on. We checked everything—the fuel pump, alternator, and idle air control valve—and couldn’t find a fault. There were no consistent trouble codes, just a generic U-code for lost communication every once in a while. On a hunch, we monitored the data stream from the ECM and noticed that the processor would momentarily drop offline right before a stall. We swapped in a pre-programmed ECM, and the problem vanished instantly. It was a classic case of internal circuit board failure in the original 2008 Avenger Engine Computer that only showed up under specific load conditions.
Signs You Need a New 2008 Avenger Engine Computer
A failing ECM can manifest in many ways. If you’re experiencing any of the following symptoms, it’s a strong indication that your engine computer needs to be replaced:
- ✔ Check Engine Light is on with communication-related codes (U-codes) or multiple, unrelated sensor codes.
- ✔ The engine cranks but refuses to start.
- ✔ Unexplained stalling or cutting out while driving.
- ✔ Severe drop in fuel economy.
- ✔ Noticeable loss of engine power and poor acceleration.
- ✔ Rough or erratic idling.
- ✔ Automatic transmission shifting issues or harsh shifts.
- ✔ The cooling fans run constantly or not at all.
Guaranteed Fitment and Compatibility
This Engine Control Module is a direct replacement for a wide range of original part numbers, ensuring perfect compatibility with your vehicle. This unit is specifically designed for the 2008 Dodge Avenger and 2007-2008 Chrysler Sebring models equipped with the 2.7L or 3.5L engines. Please verify that your original part number is on the list below to ensure proper fitment.
Compatible Part Numbers: 05033708AD, 05033708AE, 05033707AJ, 05033708AF, 05094721AA, 05094721AB, 05094721AC, 05094721AE, 05094721AG, 05094721AH, 05094721AI, 05094721AJ, 05094721AK, 05094721AL, 05094721AM, 05094721AN, 05150157AH, 05094721AO, 05094858AA, 05094858AC, 05094858AD, 05094858AE, 05094858AF, 05187343AF, 05150245AC
Replacing your faulty 2008 Avenger Engine Computer is a critical repair that restores your vehicle’s performance, reliability, and fuel efficiency. By choosing our pre-programmed module, you are selecting the fastest and most reliable path to getting your car running right again.
Frequently Asked Questions
Do I need to have this computer programmed by a dealer?
No. This engine computer comes fully programmed to your vehicle’s specific VIN. It is a true plug-and-play solution, and no further programming or flashing is required after installation.
Where is the ECM located on my 2008 Dodge Avenger?
On the 2008 Dodge Avenger, the Engine Control Module (ECM) is typically located in the engine bay, mounted to the firewall or inner fender well. It will have several large electrical connectors attached to it. Always disconnect the vehicle’s battery before attempting to remove or install the ECM.
Will this fix my Check Engine Light?
If the Check Engine Light is on due to an internal failure of the ECM, then yes, this part will resolve the issue. However, it’s always recommended to have the vehicle scanned for Diagnostic Trouble Codes (DTCs) to ensure the problem isn’t with a sensor or other component that the ECM is monitoring.
Is this a simple DIY installation?
For someone with basic mechanical skills, this is a very manageable job. The process typically involves disconnecting the battery, unplugging the electrical connectors from the old module, unbolting it, and then installing the new one in the reverse order. No special tools are usually required beyond a basic socket set.
What information do you need from me to program the module?
We require your vehicle’s 17-digit Vehicle Identification Number (VIN) to program the computer correctly. In some cases, we may also ask for the vehicle’s current mileage. This ensures all the factory settings and immobilizer information are correct for your specific car.