Restore Your Vehicle’s Electronics with a Hassle-Free Solution
Are you dealing with baffling electrical issues in your Chevrolet Orlando or another GM vehicle? Flickering dashboard lights, power windows with a mind of their own, or a security system that prevents your car from starting are classic signs of a failing Body Control Module (BCM). As an automotive technician with over two decades of experience, I’ve seen how a faulty BCM can turn a reliable vehicle into a source of constant frustration. It acts as the central nervous system for your car’s comfort and convenience features, and when it fails, chaos ensues.
This isn’t just a replacement part; it’s a complete, plug-and-play solution. We take the guesswork and high dealership costs out of the equation. By purchasing this service, you’ll send us your original BCM. We then perform a professional cloning service, transferring your vehicle’s specific VIN, security information, and option programming to this fully tested replacement module. The result? A BCM that is 100% ready to install right out of the box, with no additional programming required. This is the most reliable and cost-effective way to get your car back to normal.
Case Study: A Tricky Diagnosis
A few months ago, a 2011 Buick LaCrosse came into my shop. The owner was at his wit’s end. The radio would randomly shut off, the key fob worked intermittently, and the car wouldn’t start every other morning. He had already replaced the battery and checked the alternator. Diagnostic scans showed a slew of communication error codes, like U0140 (Lost Communication With Body Control Module). Instead of just throwing parts at it, we identified the BCM as the culprit. A cloned BCM like this one solved every single issue in one go, saving the customer over $700 compared to the dealership’s quote.
Common Symptoms of a Failing BCM
If your vehicle is experiencing any of the following, a faulty BCM could be the root cause. This 2012 Orlando BCM solution is designed to correct these problems.
- ✔ Unpredictable instrument cluster behavior (gauges dropping, warning lights on)
- ✔ Power windows, door locks, or interior lights not working correctly
- ✔ The security or anti-theft system preventing the engine from starting
- ✔ Key fob not responding or working sporadically
- ✔ Communication error codes stored in the system (e.g., U0140, U0155)
- ✔ Wipers or other accessories activating on their own
A Straightforward Guide to Installation
Installing your newly programmed BCM is a direct process. For the 2012 Orlando, the BCM is located below the center console.
- Safety First: Always disconnect the negative terminal from your vehicle’s battery before working on any electronic components.
- Locate the BCM: On the 2012 Orlando, you’ll need to access the area below the center console to find the module. For other models, refer to your service manual for the specific location (e.g., LH kick panel, under the dash).
- Disconnect and Remove: Carefully unplug the electrical connectors. They have locking tabs that must be depressed. Once disconnected, unbolt the old BCM and remove it from the vehicle.
- Install the New Module: Mount your new, programmed BCM in the same location and secure it with the original hardware.
- Reconnect: Firmly plug in all the electrical connectors until they click into place. Double-check that they are all secure.
- Power Up: Reconnect the negative battery terminal. Turn the key to the ‘On’ position (without starting the engine) and verify that your electronics are functioning correctly.
Verified Vehicle Compatibility
This BCM cloning service is compatible with a wide range of GM vehicles. Please match your part number from the list below. This module is a direct replacement for part numbers 13501737, 13579004, 13580198, 13582396, 13583450, 13586856, 13582688, 13586278, 13501739, 13577924, 13580773, and 13583451.
- Buick LaCrosse (2011-2012)
- Cadillac SRX (2011-2012)
- Chevrolet Camaro (2011 Convertible)
- Chevrolet Cruze (2012)
- Chevrolet Equinox (2011)
- Chevrolet Orlando (2012)
- Chevrolet Volt (2011, 2013)
- GMC Terrain (2011)
- Buick Regal (2011)
Note on Post-Installation Procedures: In some cases, additional steps may be needed. If your airbag light is on, a professional scan tool is required to perform the ‘Setup SDM Primary Key in BCM’ procedure. Some models may also require a Brake Pedal Position Relearn. Always consult a factory service manual for vehicle-specific instructions.
Frequently Asked Questions
How does the cloning process work?
After you place your order, we will provide you with shipping instructions. You send us your original BCM. Our technicians will then extract the unique data and program it onto the replacement module. We then ship the plug-and-play replacement back to you.
Do I need to get this programmed by a dealer?
No. The main benefit of our service is that the module arrives fully programmed to your vehicle’s VIN and security settings. This completely eliminates the need for a costly trip to the dealership for programming.
Is this a guaranteed fix for my car’s problems?
This service corrects issues directly caused by a faulty BCM. While the symptoms listed are very common for BCM failure, we always recommend a proper diagnosis by a qualified mechanic to confirm the BCM is the problem before ordering.
What is the turnaround time?
We pride ourselves on a fast turnaround. The programming is typically completed and the module is shipped back out within 1-2 business days of us receiving your original BCM.
Do I need to send my keys with the BCM?
No, you do not need to send your keys. All the necessary security information is stored within the BCM itself, which is what we transfer during the cloning process.
What if an airbag light appears after installation?
On some GM models, the BCM needs to be synced with the airbag system (SDM). If the airbag light is on after install, a mechanic with a professional diagnostic tool will need to perform the ‘Setup SDM Primary Key in BCM’ procedure to resolve it.